Twenty20 Corporation VholdR 1102, User Manual

Page: 6 / 17

Before you power up, make sure your VholdR is in the
‘Stop’ position by sliding the top record switch all the
way back against the rear door.
Note: Do not toggle the record switch or connect to a
computer until the unit is fully booted. (Approximately 15
seconds).
Press and hold the power button until the status lights
on the back light up, then release.
The front red power light will turn on.
The rear two lights will stay amber for about 10
seconds.
Next, the lens lasers will turn on for about five
seconds as the back two indicator lights turn off.
CAUTION: DO NOT stare directly into the laser beams.
Finally, the lasers will turn off and you will hear a
beep.
The VholdR is now fully booted and ready to record.
The red power light will remain on to indicate the
VholdR is on and ready to go.
You can check the status of your VholdR camera by pressing and holding the power
button for one second after the camera has finished booting.
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
rear door
record
stop
record switch
192º rotating lens
dual alignment lasers
TRail™ mounting system
power indicator
serial number charging indicator
battery slot
microSD
card slot
USB
power button
memory indicator
charging indicator
USB connection
record
stop
rear
press and hold
until lights
come on
front
push until
lights
come on
a, f
c
b
b
press and hold
for (1) second
attach leash
before using
after detaching, rotate
vertically to align and then
reattach firmly into mount
attach and adjust camera according to your riding position
(it’s no fun watching videos of the ground)
press and hold
for (1) second
rotate lens to align
lasers horizontally
Battery Status
Green light
Yellow light
Red light
No lights
Memory card status
Green light
Yellow light
Red light
Flashing Red
Power off
More than 66% full
Between 33% and 66% full
Less than 33% - time to recharge
Recharge your VholdR or power up again
More than 66% free recording space
Between 33% and 66% free recording space
Less than 33% - time to swap out cards or download
Your memory card is full, you are missing a card, or
your card has an error and needs to be formatted
(see Tips & Troubleshooting to format your MicroSD Card)
Press and hold rear button for 3 seconds or until all
lights turn off
aim lasers
record stop
hold base of
mount firmly
against
surface as
you pull
camera
away
from
velcro
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
rear door
record
stop
record switch
192º rotating lens
dual alignment lasers
TRail™ mounting system
power indicator
serial number charging indicator
battery slot
microSD
card slot
USB
power button
memory indicator
charging indicator
USB connection
record
stop
rear
press and hold
until lights
come on
front
push until
lights
come on
a, f
c
b
b
press and hold
for (1) second
attach leash
before using
after detaching, rotate
vertically to align and then
reattach firmly into mount
attach and adjust camera according to your riding position
(it’s no fun watching videos of the ground)
press and hold
for (1) second
rotate lens to align
lasers horizontally
Battery Status
Green light
Yellow light
Red light
No lights
Memory card status
Green light
Yellow light
Red light
Flashing Red
Power off
More than 66% full
Between 33% and 66% full
Less than 33% - time to recharge
Recharge your VholdR or power up again
More than 66% free recording space
Between 33% and 66% free recording space
Less than 33% - time to swap out cards or download
Your memory card is full, you are missing a card, or
your card has an error and needs to be formatted
(see Tips & Troubleshooting to format your MicroSD Card)
Press and hold rear button for 3 seconds or until all
lights turn off
aim lasers
record stop
hold base of
mount firmly
against
surface as
you pull
camera
away
from
velcro
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
S/
NO 120
700 0 0 3 3
rear door
record
stop
record switch
192º rotating lens
dual alignment lasers
TRail™ mounting system
power indicator
serial number charging indicator
battery slot
microSD
card slot
USB
power button
memory indicator
charging indicator
USB connection
record
stop
rear
press and hold
until lights
come on
front
push until
lights
come on
a, f
c
b
b
press and hold
for (1) second
attach leash
before using
after detaching, rotate
vertically to align and then
reattach firmly into mount
attach and adjust camera according to your riding position
(it’s no fun watching videos of the ground)
press and hold
for (1) second
rotate lens to align
lasers horizontally
Battery Status
Green light
Yellow light
Red light
No lights
Memory card status
Green light
Yellow light
Red light
Flashing Red
Power off
More than 66% full
Between 33% and 66% full
Less than 33% - time to recharge
Recharge your VholdR or power up again
More than 66% free recording space
Between 33% and 66% free recording space
Less than 33% - time to swap out cards or download
Your memory card is full, you are missing a card, or
your card has an error and needs to be formatted
(see Tips & Troubleshooting to format your MicroSD Card)
Press and hold rear button for 3 seconds or until all
lights turn off
aim lasers
record stop
hold base of
mount firmly
against
surface as
you pull
camera
away
from
velcro
a
b
c
d
e
f
10 11 Powering Up VholdR Camera Status
Powering Up VholdR Camera Status