Tvone MAGENTA Pathfinder 500 Series User Manual Download Page 6 | Manualshive

Page: 6 / 32

background image

3

PDF-MG-KVM-53x-V1.00

About your Pathfinder 500 series device

The Pathfinder 500 series includes a DVI encoder and decoder, capable of extending a 1080p signal up
to 20 km (12 miles).

MG-KVM-531 encoder rear panel

DVI IN DVI-I in. Connect to the PC you want to control.

Audio in from PC.
Connect to the PC with 3.5 mm jack.

RS232 Connect to a control device with Ethernet cable.

Audio out to PC.
Connect to the PC with 3.5 mm jack.

DVI LOOP

OUT

DVI-I out. Connect to a monitor.

12VDC Connect to 12 V power supply.

USB Connect to USB port of PC.

KVM-LINK Depending on your SFP, connect to one of the following:

▪

Single-mode optical fiber cable

▪

Multi-mode optical fiber cable

▪

Ethernet cable

«
...
4
5
6
7
8
...
»

Summary of Contents for MAGENTA Pathfinder 500 Series

































Reviews:

No comments

Related manuals for MAGENTA Pathfinder 500 Series

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: Badger Basket Pages: 3

Brand: BADLANDS Pages: 2

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: National Instruments Pages: 2

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: WAGO Pages: 16

Brand: Trane Technologies Pages: 8

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Graco Pages: 166

Brand: Baby Trend Pages: 10

ZoneSense Plus AS

Brand: Halma Pages: 58

STRATOSTM INSPIRE

Brand: Ultrahaptics Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands