manualshive.com logo in svg

Tuthill M-D Pneumatics PD PLUS 17/46 Series, Installation Operation Maintenance Repair Manual

Share
Download
Tuthill M-D Pneumatics PD PLUS 17/46 Series Installation Operation Maintenance Repair Manual Download Page 32

32

8.3  SPECIAL INSTRUCTIONS - 64/67 SERIES

Continue assembly:

A.  Prepare cover (6). Place fl ange side down, install fi rst of two snap rings (78) into innermost groove.  

Press in fi rst of 2 ea. Mechanical seals (54A) lightly silicone outer case of seal.  Press seal with carbon 
side down until seated against the snap ring .  Careful not  to distort snap ring.

B.  Install second snap ring (78) into outer groove.   Place mating ring from 1st seal into cover with lap 

surface up.  Press second mechanical seal (54) in, carbon side groove down until seated against outer 
snap ring.  Carbon will seal against mating ring when cover is installed on drive shaft.

8.3.1  DRIVE SHAFT ASSEMBLY

A.  Install one thin spacer (74) onto drive shaft so it is next to bearing with groove out.  Install one o-ring 

(75) to seat in the groove of the spacer.  Lightly oil face of mating ring, install onto shaft with lapped 
surface out.  Install large spacer (77) with groove side facing mating ring.  Install thin spacer (74) with 
groove out, install o-ring (75) so it will seat into groove.

B.  Remove temporary hold down bolts, place bead of silicone around periphery of the end plate (4) 

encircling each bolt.  Install gear end cover and tighten bolts.  Install large spacer (77) with groove out, 
install free end spacer, install dust cover (82) and lock nut.  Install pipe plug (85) into bottom nose piece 
in cover (6) silicone plug.

C.  Fill with oil until oil can be seen in the middle hole, install pipe plug (85).  Continue to fi ll to proper level.  

Wait 2 minutes before installing the last pipe plug (85) to make sure proper oil level is maintained.

Summary of Contents for M-D Pneumatics PD PLUS 17/46 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands