Turnigy TGY-i10, Instruction Manual

Page: 30 / 60

Digital proportional radio control system
29
21.11.
辅助通道
Auxiliary Channels
辅助通道 当飞机结构设定完成后，为剩下的通道选择一个 开关、旋钮、逻辑开关 或 摇杆 作为 辅助通道 。因飞机结构默认为
四通道固定翼，所以默认辅助通道为
CH5~CH10;
点触此功能下需 设置的 辅助通道 ，选择一个 开关、旋钮、逻辑开关 或 摇杆 对通道进行设置。
如图
21
.
14
所示：设置 辅助通道
CH5
，
并 选择
SwD
向上控制该通道的开启，此时拨动开关
SwD
向下时， 显示舵机 （ 显示舵
机 功能见说明书
P29
页）里通道显示为左边
100
位置。
21.10.
收油门
Throttle Down
此功能用来调节 低怠速 的比率和 熄火 功能的 开启 或 关闭 ，低怠速从可0~50%间调节。此功能可分别在
5
个 状态 下设定。
低怠速 功能开启时油门输出将会减去设定的比率值。
熄火 功能开启时油门输出会降到最低。
熄火 功能优先于 低怠速 功能；当 熄火 功能开启后调节油门摇杆时油门没有输出。默认 低怠速 和 熄火 功能均为 关闭 ， 低怠速
默认比率为
10%
。
点触选择两个开关
(SwA~SwH
、
LSw)
分别控制这两个功能的 开启 或 关闭 。当飞机结构没有 引擎 （如 滑翔机 ）将没有 收油
门 功能，主菜单中没有此功能图标。
点触选择两个开关开启 低怠速 和 熄火 功能，滑动转轮调节 低怠速 功能数值。
如图
21
.
12
所示： 低怠速 和 熄火 功能已开启，调节 低怠速 至
20%
，因为 熄火 功能已开启，油门通道将没有输出。
(
Pic 21.12)
(
Pic 21.14)
拨动开关
SwD
向下时
(
Pic 21.13)
Throttle down function is to enable idle down rate adjustment and throttle cut function turned on
or off . Modify the rate from 0% to 50% after idle function is applied. This function can be set in five
conditions .
Idle down: the throttle output minus the rate set in advance after this function is applied.
Throttle cut: the throttle output will be in its lowest point after this function is applied.
Throttle cut function is prior to idle down function. There is no output while moving throttle stick
if throttle cut function is applied. Idle down function and throttle cut function are turned off by
default. The default value of idle down is 10%.
These two functions can be assigned to 2 switches (SwA~SwH
、
LSw). If the airplane does not
have an engine , this icon will not be displayed.
Select two switches to enable or disable idle down and throttle cut function and move the wheel
to modify the corresponding value after activating this function.
As shown in the picture21.12: The
idle down function and throttle cut are applied, and adjust
the idle down to 20%. There is no output of throttle channel.
Assign the auxiliary channel a switch , a knob , a logic switch or a stick
after finishing the airplane structure setting. The default structure is 4-channel
fix wing, so auxiliary channels are from Ch5 to Ch10.
Touch the auxiliary channel needed and select a switch, a knob, a logic
switch or a stick to control this function.
For this example: Select CH5 as
auxiliary channel and push SwD upward
to enable this function. At this time, the channel in Servo display is displayed
as shown in picture 21.14
Push swd downward
功能说明 ：
此功能分为两项，第一项为 怠速 设定，第二项为 油门锁定 设定，它们都是在调试及调整模型时使用的。其中怠速用于有引擎的模
型让它保持低转速而不熄火。而 油门锁定 则是让模型油门完全让遥控器锁定不做输出。
功能说明：
当模型装配调整基本完成后，如果发现还有一些结构功能没有设置，此时可通过 辅助通道 来进行辅助调整完成。
Function Details :
The model function allows users to set additional auxilary channels if the
model has more than the default 4 channels. Some aircraft have more than
four auxilary channels, so these additional channels can be modified using
this function.
Function Details:
This function contains two options: option one is idle setup and option two is throttle hold Two
options would be set when you adjust models. The idle is useful for the models with engines and make
models keep low rpm without shutting down. And the
throttle hold is to completely lock model’s throttle
without shutting down.