TURFCO 85874 Operator'S Manual Download Page 11

Page: 11 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

Steering the Machine

Now you are ready to try the steering and driving the machine on the parking lot. Like your car, the Turfco T3000i

Applicator steers uses a steering wheel. A full spin to the right will give you a full right turn and a full spin to the left

give you a full left turn.. The steering wheel is equipped with a wheel spinner knob to make this easier.
Drive the machine in all modes; fast, slow, turns, figure 8’s and reverse backing. One thing you must get accustomed

to is steering and stopping of the machine. Do this for at least 10 minutes

before we move on to the other controls.
● Drive the T3000i Applicator ahead slowly 10 feet and make a 180º degree

turn using the steering wheel. Continue doing this several times gradually

increasing the speed. Do not try to make a full 180º degree turn at full speed

until you are well accustomed to the machine.
● Continue with other driving maneuvers such as figure “8’s”, circles, 90º

degree turns and many 180º degree turns. The machine is designed to do a

full 180º degree turn in 9 feet, to match the effective operation width of the

spread and spray. Therefore the operator must practice this turn until they

have it mastered.

To operate the Forward Speed Control Pedal, step on the

yellow colored pedal (located on the operators platform)

and

slowly

press down. Notice that as you press the pedal

the forward speed control handles are moving forward. The

further you press the pedal, the further the speed control

handles move. As long as pressure is applied on the pedal,

the speed control will remain in forward position.

● Try this operation a number of times so you become

very familiar with the operation of the Forward Speed

Control Pedal. You will need to know this for later

operation of the machine.

Note: The pedal is for forward movement only, the pedal

is not for reverse.

Using 3-1/2 MPH Speed Lever

(See Figure 5)

The T3000i Applicator has a 3-1/2 mph speed lever

mounted on the right hand forward/reverse speed control

handle to provide a slower ground speed. The lever limits

the amount of forward movement of the speed control

handle. Ground speed will be approximately 3-1/2 mph

(5.6 Km/h).

THE 3-1/2 MPH SPEED LEVER IS FOR

SPREADING ONLY - DO NOT USE WHEN SPRAYING.

● To operate the 3-1/2 MPH speed lever, simply move the

lever in a forward position and set. When the forward

speed control handle is moved forward, the lever will

touch the support bar and stop any further speed

increase. You will be going at a slower 3-1/2 mph

speed.

Refer to the 3-1/2 mph spreader calibration.

● To return to full speed operation, return the lever in the

off position and set.

The 3-1/2 mph speed lever can be used with or without the

speed control pedal.

9 FOOT

TURNING

CIRCLE

OP85874-06

OPERATION

FIGURE 5

3-1/2 MPH

SPEED

CONTROL

LEVER

OP85872-14RevC

SPEED

LEVER

SPEED

LEVER

OFF

RIGHT HAND

SPEED

CONTROL

HANDLE

SPREADING ONLY!

DO NOT USE WHEN

SPRAYING.

Summary of Contents for 85874










































Search results

Summary of Contents for 85874

Reviews:

Related manuals for 85874

Brands by name

Popular brands

TURFCO 85874, Operator'S Manual

Search results

Summary of Contents for 85874

Reviews:

Related manuals for 85874

Brands by name

Popular brands