TURFCO 85874 Operator'S Manual Download Page 31

Page: 31 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

SPREADER CALIBRATION

Material drops out of the hopper just behind the center of

the wheel (spinner wheel rotates clockwise).
Product that lands closer the center of the spinner wheel

has father to travel on the wheel as it moves to outside edge

to be thrown. As a result of staying on the wheel longer, it

gets thrown out last - or to the right.
Product that lands closer the outside edge of the spinner

wheel is thrown first. It is on the wheel for a shorter time and

is thrown out first - or to the left.
Adjust your Accuway to give a even balanced left to right

spread. Start with an empty hopper -

● Open the gate all the way. Look straight down into the

opening, you will see the black plastic Accuway wedge.

● Screw the adjuster knob (on front of hopper) so the

Accuway moves into the gate opening. Move the

Accuway far enough forward so that 3/8” of an inch is

visible in the opening.

● To adjust the throw more to the left, increase the amount

that the Accuway is visible in the opening.

● To adjust the throw more to the right, decrease

the

amount that the Accuway is visible in the opening.

● Continue moving the wedge until you get the left to right

balance spread of the product.

Note: The Accuway pattern adjuster needs to be changed when the gate opening size is changed (recalibrated) or product type is changed.

“ACCUWAY”

SPREAD

PATTERN

ADJUSTER

OP85874-27

3/8” INCH

GATE

OPENING

FRONT OF MACHINE

FIGURE 21

FRONT

EDGE

OF GATE

OP85874-33

If It Throws to Much

to the Right - The

Accuway Is Need To

Be Further In To The

Gate Opening.

Adjust The Accuway To Get a Spread That

Is Balanced Left and Right

FRONT OF MACHINE

If It Throws to Much to the

Left - The Accuway Is Too

Far In To The Gate

Opening.

SPINNER

WHEEL

GATE

OPENING

ACCUWAY

FIGURE 22

Setting the “Accuway” Spread Pattern Adjuster (See Figure 21 and Figure 22)

The Accuway Spread Pattern Adjuster is a black plastic wedge that is under the spreader gate opening. When

the gate is opened, the Accuway wedge controls where the material lands on the spinner wheel. This affects

the throw of the material. If the material lands closer to the center of the wheel, it spreads more material to the

right. If it lands closer to the outside edge of the wheel, it spreads more material towards the left.

Summary of Contents for 85874










































Search results

Summary of Contents for 85874

Reviews:

Related manuals for 85874

Brands by name

Popular brands

TURFCO 85874, Operator'S Manual

Search results

Summary of Contents for 85874

Reviews:

Related manuals for 85874

Brands by name

Popular brands