background image

 

 

 

Status: 13.08.2019 

 

 

Translation of the original Installation and operating instructions nnn 

TÜNKERS Maschinenbau GmbH 

 

5.2

 

Initial Start-up 

Employees of the TÜNKERS Maschinenbau GmbH, the system manufacturer, or the operating company 
establish the connection according to the circuit diagram/pneumatic diagram and the setup during initial 
start-up. 
 

 

6

 

Operation

 

The Machine must only be used according to its intended use (see chapter 1.8 "Intended use"). Specific 
requirements and safety instructions apply for the different operating modes of the Machine. 
The Machine is run in the following operating modes: 

 

Automatic mode 

 

Manual mode (set-up mode) 

 

The operator/manufacturer of the complete system is responsible for executing the operating modes. 
The work involved with the operation, tooling, maintenance, and fault repair can be assigned to these 
operating modes. 

 

 

6.1

 

Safety instructions 

 

 

WARNING 

Observe safety instructions! 

 

Observe the safety instructions in Chapter 2 "Safety instructions" and in particu-
lar Chapter 2.2 "General safety instructions". 

 

 

6.2

 

Operating the Retractable Locating and Expanding Pin SDZ 40 F. 

The Machine 

doesn’t have any controls. 

The Machine is operated via the control of the complete system, 

in which the Machine is used. 

 

 

NOTE 

For information on operation, observe the operating manual of the complete system. 

 

 

6.3

 

Basic checks before and during operation 

Familiarise  yourself  with  your  work  environment  before  starting  work.  Externally  check  (visually)  the 
Machine for visible defects at least once per shift. Before starting work, the service and maintenance 
intervals must be followed in line with the maintenance schedule. 
Before switching on the  Machine and during operation, monitor the  Machine area for anomalies at all 
times. The following features may indicate irregularities the Machine are switched on: 

 

increased noise, noise irregularly occurring/unusual noises. 

 

unusual smell 

 

leaks in the pneumatic system. 

 

reduced performance during operations 

 

incorrectly positioned 

Shut down the Machine immediately upon the first signs of any of the above issues. Inform maintenance 
staff immediately for an accurate assessment of the technical status. 
Maintenance  staff  must  then  decide  if  operation  can  continue  without  limiting  the  functionality  of  the 
Machine. If a failure is expected due to damage, perform repairs immediately. 

 

 

 

Summary of Contents for SDZ 40 F



















Reviews: