Tuncmatik NEWTECH PRO User Manual Download Page 29 | Manualshive

Page: 29 / 35

background image

28

Battery mode

Description

When the input voltage is beyond the acceptable range or power failure,
UPS will backup power from battery and alarm will beep every 4 seconds.

LCD display

Bypass mode

Description

When input voltage is within acceptable range and bypass is enabled, turn
off the UPS and it will enter Bypass mode. Alarm beeps every two minutes.

LCD display

Battery Test

Description

When UPS is in AC mode or CVCF mode, press “Test” key for more than 0.5s.
Then the UPS will beep once and start “Battery Test”. The line between I/P
and inverter icons will blink to remind users. This operation is used to check
the battery status.

LCD display

«
...
27
28
29
30
31
...
»

Summary of Contents for NEWTECH PRO




































Reviews:

No comments

Related manuals for NEWTECH PRO

Brand: Eaton Pages: 25

Brand: Tripp Lite Pages: 12

miniUPS ALS Series

Brand: YAMABISHI Pages: 26

Zenergy Station 2000

Brand: INFOSEC UPS SYSTEM Pages: 27

XP Pro evolution

Brand: INFOSEC UPS SYSTEM Pages: 72

Brand: AKKU SYS Pages: 12

Brand: HPE Pages: 25

UPS HALLEY/E Series

Brand: Astrid Pages: 56

Brand: Powertronix Pages: 46

Blazer Vista 1000

Brand: Atek Pages: 12

Brand: Xtreme Power Conversion Pages: 49

OPTIMA-RT10-10K

Brand: Xmart Pages: 48

Brand: Xtreme Power Conversion Pages: 9

Brand: Uninterruptible Power Supply Pages: 38

Brand: CyberPower Pages: 1

Satellite 5000 Series

Brand: Toshiba Pages: 225

Brand: Eaton Pages: 2

Power Xpert 9395 High Performance

Brand: Eaton Pages: 246

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands