TSPROF K03 User Manual Download Page 13

23

24

3.  

Lock the sharpening angle using the 

tumbscrew

 if desired, as illustrated below.

Before changing the angle again later, remember to loosen the locking screw.

4. 

 Loosen the near stopper, and set the near edge of abrasive stone on the farthest edge of the blade, 

leaving about 1.5 - 2 cm of overlap.

5.  

Move near stopper to the hub and tighten the thumbscrew.

Adjustment of the far stopper is similar.

7. CALIBRATION

The TSPROF system is carefully calibrated during production. Settings or calibration can sometimes 
be disrupted in transportation, or if the unit has been disassembled for some reason. 
Deviations less than or equal to <= 0.3 ° are not critical. It is not recommended to make adjustments 
of noncritical deviations. All adjustments should be performed on a flat, level, and solid surface.

C

alibration of the pivot-arm

Option 

1.

1. Place the digital protractor on the reference plane (the base of the body, as illustrated) and zero it.
2. Move the digital protractor to the pivot-arm. If the difference is less than 1°, adjustment is not 
needed. If adjustment is needed, perform the following actions.
3. Hold the pivot-arm by hand, and loosen the central lock-nut with a 10mm wrench. Slightly turn 
the pivot-arm to achieve a zero value of the digital protractor. While still holding the pivot-arm 
in place, tighten the lock-nut.

1. 

2. 

3.

Option

 2.

1. Place a machinist's ruler vertically touching the edge of the pivot-arm and rest it on a flat table 
surface. Observe and note the measurements on both sides of the arm.
2. Hold the pivot-arm by hand, and loosen the central lock-nut with a 10mm wrench.  
Slightly turn the pivot-arm to achieve equal measurements on both sides. 
While still holding the pivot-arm in place, tighten the lock-nut.

1. 

2. 

C

lamp angle calibration

Calibration is sometimes required to equalize the asymmetry of the angles after pivot-arm rotation.  
A digital protractor is required for this calibration step.  The system should be firmly located on a 
flat and level surface.

Summary of Contents for K03
















Reviews: