TSPROF K03 User Manual Download Page 11

19

20

4. PREPARING FOR WORK

 

Option

 1.

1. Apply felt pads (1

0

E) from the spare parts kit to the contact surfaces of the C-Clamp.

2. On the underside of the body, attach 5 small clear rubber bumpers (1

0

F) from the spare parts kit.

3. Fix the body to the table with C-Clamp.

Option

 2. 

1. Stick 5 large clear rubber bumpers (1

0

F) from the spare parts kit to the underside of the base, 

as illustrated.
2. Locate the sharpener body in the hollow part of the base. Attach by tightening the two large 
thumb-screws.

Option

 1

Option

 2

5. ASSEMBLY

1. Assemble the abrasive holder, then remove the far stopper along with its damping spring.

2.  

 Install the abrasive holder into the hub sleeve (1), apply a drop of lubricant, then adjust the damping 

spring and stopper (2).

1

2

3

.  Adjust the pivot-arm tension. 

T

urn the tension wheel, to set an appropriate pivot-arm tension. 

Set tension high enough that the pivot-arm doesn't rotate unintentionally during the sharpening 
process.

4. Install the selected clamp(s) on the pivot-arm and tighten the thumbscrew(s).  
You can use any TSPROF clamp. Space the clamps at an appropriate distance from each other, 
depending on blade length and shape.

5.

 Loosen the far (2) and near (1), clamping screw(s), and insert the blade to be clamped. Use a piece 

of the leather or masking tape on the blade at the clamp contact point, to avoid  marring the blade. 
Tighten near clamping screw(s) (1) slightly, then tighten the far clamping screw (2) more firmly. 
Clamp jaws should be parallel. To release the blade, loosen the screws in the reverse order.

* Illustration and instructions are for a blade for a full flat grind

1

2

 
If the knife has a tapered blade, first lightly tighten the near clamping screws (1),  
then the far screw (2). Slightly loosen the near screws while tightening the far screw.  
The jaws should be at an angle to each other, as illustrated below. If the far clamping screw is not  
long enough, replace it with a longer M4x16 (14G) from the spare parts kit.

Summary of Contents for K03
















Reviews: