TSI Instruments 3786 Operation And Service Manual Download Page 75

Page: 75 / 83

Firmware Commands

B-17

Example D Record:

D,2,0,2.27e3,6.0,5.875,66784,0,308

S Record (status)

S, FL, AP,GT,OT,CT

Status Record Identifier

Aerosol flow rate in cm

/min

Absolute Pressure in millibar

Saturator Temperature in degrees Celsius

Growth tube Temperature in degrees Celsius

Optics Temperature in degrees Celsius

Example S Record:

S,300,970,12.0,75.0,75.0

Z Record (scanning data)

Z,Mode,Flags,RN,N0,N1… ,N9

Z Record

Identifier

Mode Current Operating mode (5 or 6)
Flags See status flags
RN

Record number - (1 to 600)

Equivalent number of particles counted in tenth second (0 to 99999999) based on live-
corrected counts or the photometric value.

Example Z record:

Z,5,0,12,0,0,0,12,182,518,641,896,887,871

A Record (raw analog -- diagnostic only)

A,a,b,c,d,e,f,g,h,i,j,k,l,m,n,o

A Record

Identifier

a-o raw analog values (bits)

Example A record:

A,2382,3194,1,1108,4095,4095,2735,1284,518,641,896,2278,821,819,1958

C Record (flow and temperature control - diagnostic only)

C,a,b,c,d,e,f,g,h,i,j,k,l

C Record

Identifier

a - l control bit values

Example C record:

C,2413,2422,2166,2276,2276,1468,821,820,2894,821,820,1011,2210,2222,2012

Summary of Contents for 3786



















































































Search results

Summary of Contents for 3786

Reviews:

Related manuals for 3786

Brands by name

Popular brands

TSI Instruments 3786, Operation And Service Manual

Search results

Summary of Contents for 3786

Reviews:

Related manuals for 3786

Brands by name

Popular brands