TSI Incorporated portacount pro 8030 Operation And Service Manual Download

Page: 47 / 93

Chapter 5

Operating Modes and User Interface

This chapter describes the operating modes of the P

ORTA

OUNT

Respirator Fit Tester

and describes the options available through the user

interface (touch screen).

Modes of Operation

There are two modes of operation: External Control (using F

™

software) and Stand-alone.

External Control
Mode

The P

ORTA

OUNT

Respirator Fit Tester is

operating in External Control Mode when it is
being controlled by F

™

software running

on your computer. If you attempt to perform an
operation from the P

ORTA

OUNT

touch

screen while it is being controlled by F

™

software, a message appears asking if you want
to unlock the P

ORTA

OUNT

fit tester.

If you

respond

YES

, the P

ORTA

OUNT

fit tester

breaks the connection with the computer (and the
F

™

software) and begins to operate in

stand-alone mode

Note:

You may lose data already collected in the

active flash drive database.

Refer to the online help of the F

™

software

for operating details.

Stand-alone Mode

The P

ORTA

OUNT

Respirator Fit Tester is

operating in Stand-alone Mode when it is

NOT

controlled by F

™

software running on your

computer. When you turn the P

ORTA

OUNT

fit tester on, the instrument automatically begins
a warm-up period. When the warm-up period is
over, a beep sounds and the touch-screen display
appears. The P

ORTA

OUNT

fit tester is now

ready for Fit Testing and other stand-alone
operations.

Summary of Contents for portacount pro 8030






























































































Search results

Summary of Contents for portacount pro 8030

Reviews:

Related manuals for portacount pro 8030

Brands by name

Popular brands

TSI Incorporated portacount pro 8030, Operation And Service Manual

Search results

Summary of Contents for portacount pro 8030

Reviews:

Related manuals for portacount pro 8030

Brands by name

Popular brands