TSI Incorporated 8026 Operation And Service Manual Download Page 3

 

 

Copyright ©  

TSI Incorporated / Revision M / 2000

–2016 / All rights reserved. 

Address 

TSI Incorporated / 500 Cardigan Road / Shoreview, MN  55126 / USA 

Fax No. 

(651) 490-3824 

LIMITATION OF WARRANTY AND LIABILITY

 (effective February 2015) 

(For country-specific terms and conditions outside of the USA, please visi

www.tsi.com

.) 

Seller warrants the goods, excluding software, sold hereunder, under normal use and 
service as described in the operator's manual, to be free from defects in workmanship and 
material for 

12 months

, or if less, the length of time specified in the operator's manual, 

from the date of shipment to the customer. This warranty period is inclusive of any statutory 
warranty. This limited warranty is subject to the following exclusions and exceptions: 

a.  Hot-wire or hot-film sensors used with research anemometers, and certain other 

components when indicated in specifications, are warranted for 90 days from the date 
of shipment;  

b. 

Pumps are warranted for hours of operation as set forth in product or operator’s 
manuals; 

c.  Parts repaired or replaced as a result of repair services are warranted to be free from 

defects in workmanship and material, under normal use, for 90 days from the date of 
shipment;  

d.  Seller does not provide any warranty on finished goods manufactured by others or on 

any fuses, batteries or other consumable materials. Only the original manufacturer's 
warranty applies; 

e.  This warranty does not cover calibration requirements, and seller warrants only that the 

instrument or product is properly calibrated at the time of its manufacture. Instruments 
returned for calibration are not covered by this warranty;   

f.  This warranty is 

VOID

 if the instrument is opened by anyone other than a factory 

authorized service center with the one exception where requirements set forth in the 
manual allow an operator to replace consumables or perform recommended cleaning;   

g.  This warranty is 

VOID

 if the product has been misused, neglected, subjected to 

accidental or intentional damage, or is not properly installed, maintained, or cleaned 
according to the requirements of the manual. Unless specifically authorized in a 
separate writing by Seller, Seller makes no warranty with respect to, and shall have no 
liability in connection with, goods which are incorporated into other products or 
equipment, or which are modified by any person other than Seller. 

The foregoing is 

IN LIEU OF

 all other warranties and is subject to the 

LIMITATIONS

 stated 

herein. 

NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR 

PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE

WITH RESPECT TO 

SELLER’S BREACH OF THE IMPLIED WARRANTY AGAINST INFRINGEMENT, SAID 
WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND EXCLUDES 
CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS. BUYER’S EXCLUSIVE 
REMEDY SHALL BE THE RETURN OF THE PURCHASE PRICE DISCOUNTED FOR 
REASONABLE WEAR AND TEAR OR AT SELLER’S OPTION REPLACEMENT OF 
THE GOODS WITH NON-INFRINGING GOODS.  

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR 
BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES, 
INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED 
ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL 
BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE 
PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE 
GOODS. IN THE CASE OF SOFTWARE, SELLER WILL REPAIR OR REPLACE 
DEFECTIVE SOFTWARE OR IF UNABLE TO DO SO, WILL REFUND THE PURCHASE 
PRICE OF THE SOFTWARE. IN NO EVENT SHALL SELLER BE LIABLE FOR LOST 

Summary of Contents for 8026




















Reviews: