TSC TTP 243 Pro Service Manual Download Page 32 | Manualshive

Page: 32 / 43

background image

29

TTP-243 Pro/ 243E Pro/ 342 Pro
Bar Code Printer

4.9 Ribbon Sensor (Receiver) Replacement

1. Follow the instructions in Section 4.1 to remove all the connectors on mainboard.

2. Take out the mechanism.

3. Remove the screws, springs and spring bushing on both sides of the mechanism.

Spring Installation on Left Side and Right Side

Note: The left side spring and the right side spring are different in shape. The right

side spring has a straight end, when the left side spring has an end that is
curved 90 degrees.

4. The main mechanism is divided into upper mechanism and lower mechanism.

5. The ribbon sensor (receiver) is located in the upper mechanism.

6. Remove the screws on the ribbon sensor cover.

Ribbon Sensor Cover

Flat Tap Screw

Sensor Cover

Print Head

«
...
30
31
32
33
34
...
»

Summary of Contents for TTP 243 Pro












































Reviews:

No comments

Related manuals for TTP 243 Pro

Brand: zenpert Pages: 34

Brand: Baracoda Pages: 23

FuzzyScan FA460

Brand: Cino Pages: 67

Tire and Rubber

Brand: Metrologic Pages: 1

Brand: Franklin Pages: 82

Brand: Allen-Bradley Pages: 115

Brand: Conceptronic Pages: 21

Brand: ARTDEV Pages: 2

Brand: Atid Pages: 49

Brand: Xtool Pages: 19

Brand: SICK Pages: 44

Brand: SICK Pages: 48

Brand: SICK Pages: 77

Brand: NESS ID TECK Pages: 15

Brand: Datalogic Pages: 292

Brand: Agrident Pages: 43

Brand: ITV Pages: 4

Brand: Approx Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands