TSC TDP-243 Series Page 32 Service Manual Download | Manualshive

Page: 32 / 69

background image

29

TTP-243 Bar Code Printer
Service Manua

l

3.13 Mainboard Replacement

1. Turn off the printer power.

2. Remove the power cord and RS-232 and/or parallel port cable.

3. Open the top cover of the printer.

4. Remove the printer front panel.

Fig. 3.14 Remove the front cover

in the direction of the arrows

5. Remove the two screws and the metal cover.

Fig. 3.15 Remove the screws

and metal cover

Screws

Metal Cover

«
...
30
31
32
33
34
...
»

Summary of Contents for TDP-243 Series






































































Reviews:

No comments

Related manuals for TDP-243 Series

Brand: Datalogic Pages: 160

BOOKMAN III BDF-4045DL

Brand: Franklin Pages: 28

Brand: Netum Pages: 21

Brand: NAPCO Pages: 2

Gryphon M 00 Series

Brand: Datalogic Pages: 18

Brand: Unitech Pages: 2

Brand: Ectaco Pages: 26

Brand: Access IS Pages: 34

Brand: HikRobot Pages: 111

Brand: Pocketbook Pages: 23

Brand: Pocketbook Pages: 45

Brand: E-Seek Pages: 32

Brand: VIVOpay Pages: 18

Brand: Zio Pages: 13

Brand: Manhattan Pages: 94

Brand: SmarTerminal Pages: 33

Brand: Ecom Pages: 60

Brand: Xcellon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands