Trusted Clean TPL-17-200-CE-HEAT-TCP, Owner'S Manual, Page: 6 / 13

CLEANING UPHOLSTERY
Cleaning upholstery with success requires a good knowledge of the type of fabric you will work on. Look for
the cleaning instructions label sewn on the underside of the furniture for the recommended method of clean-
ing. If it calls for dry cleaning, do not attempt to clean by wet extraction otherwise damage to the fabric could
occur. Extraction works perfectly on most synthetic fabrics including synthetic velvets.
Before proceeding, test the fabric for colourfastness. Apply a small amount of cleaning solution on the fab-
ric in an inconspicuous spot. Wait 2 to 3 minutes and rub the area with a white terry cloth towel. If no color
comes off the towel, the fabric should be safe to clean. If a little color comes off, there is some risk of colors
running when you clean. It may be possible to stabilize colors by cleaning with an acidic rinse.
1. Prepare the machine in the same manner as for carpet cleaning (see Preparing the Machine) except
attach the upholstery tool to the vacuum hose. Connect the solution hose. Pour hot water into the
solution tank. Add recommended amount of cleaning concentrate into the solution tank. Turn on the
vacuum and pump switches.
2. Adjust the pump “operating pressure” to 50 PSI for upholstery cleaning (See Preparing the Machine).
3. Clean with the upholstery tool using as little solution as possible. Make overlapping passes to prevent
streaking. Go over the area you just cleaned without depressing the lever (vacuum only) and gauge the
amount of moisture extracted through the view window for dryness. On heavily soiled areas like
arm rests, pre-treat with a recommended pre-spray solution or hold the upholstery tool a few inches
above the fabric and press lever to spray on the solution before making a pass.
DAILY MAINTENANCE
1. Always keep the machine clean inside and out.
2. Pour 2 gallons of clean hot water in the solution tank. Turn on and flush the entire system through the
wand nozzles for about a minute to prevent build-up.
3. Remove dirt and lint build-up inside the filter screen in the recover tank. Lint should be cleaned off so that
air flow is not impeded.
4. Check the solution tank strainer in the solution tank. If lint has accumulated in the screen, remove and
rinse it in clear running water.
PERIODIC MAINTENANCE
All EDIC machines are engineered and built to require a minimum of maintenance. But like any machine,
it does require some care to keep it in optimum working condition. Careful attention to these maintenance
instructions will give you maximum operating performance and will increase the life expectancy of your ma
-
chine.
• Solution Lines and Fittings: Flush the machine at least once a month with a solution of 3 parts water with
1 part white vinegar in order to neutralize the alkaline residue left by the cleaning solution.
• Quick Connect Coupler: Spray with WD-40 or equivalent lubricant to prevent coupler from sticking.
• Drain Valve: Apply light oil on gate seals. If machine has to be stored, leave the gate valve open.
• Solution Pump: The same above procedure used on the solution line and fittings applies to the pump.
GALAXY 2000WX-HR and KX-HR (BASE) PARTS LIST
ITEM # WX PART # KX PART # DESCRIPTION QTY
1 C00297 #8 X .25 PAN HEAD 1
2 J11863 HOSE, 3 IN 1
3 J00639 SCREW CLAMP, 1.63-2.43 IN 3
4 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 22 IN LG 1
5 F11178-BLK INTERCOOLER, GALAXY, BLACK 1
6 C00273 LOCKNUT, 1-4 X 20, NYLON, SS 16
7 C00233 WASHER, FLAT, .25 IN 26
8 E00449 GROMMET 6
9 C00284 SCREW, 10-32 X .375 GROUND 2
10 B11150 GROUND WIRE, GALAXY 2
11 G00520-1L G02517-1 WX : VACUUM, 135IN, 115V, 5.7; KX :VACUUM, 147IN., 115V, 5.7IN 2
12 J00657 HOSE CLAMP, 2 IN SLDPRT 1
13 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 4 IN LG 1
14 C00261 NUT, .25-20, HEX 10
15 C00254 LOCK WASHER, 1-4 IN SPLIT 1
16 D11134 VAC PLATE 1
17 C11189 SCREW, 1-4 X 20 X 4.5 IN, HEX 5
18 C02312 LOCKWASHER, .25IN. INTERNAL STAR 1
19 C11516 SCREW, 1-4 X 20 X 4.5IN FLAT HEAD, PHILIPS 1
20 A00111 NIPPLE, .25 IN 1
21 A00052 90 ELBOW, .285MP X .25FP 4
22 A00161 TEE, .25 FP, BRASS 1
23 A00121 FITTING, .25MP X .25FP, BRASS 1
24 C11244 WASHER, .56 X 1.5 X .05 5
25 A00104 QD, 1-4M X 1-4FP, BRASS 1
26 A00154 90 ELBOW, .25 NPT X .25 NPT 3
27 C11560 WASHER, .93ID X 1.5 OD 1
28 HOSE ASSY, 13 IN X .25HP 1
29 G13133 VALVE, REGULATOR, 200 PSI 1
30 G00516-3 GAUGE, 0-600PSI 1
31 C11440 SPACER, HEATER MOUNTING PLATE 4
32 K10510 PLUG, 1.25IN, BLACK 1
33 C02322 HEX BOLT, 1-4 X 20 X 1.75IN 4
34 D010379 HEATER MOUNTING PLATE 1
35 C11165 SCREW, #8 X 1IN, PAN, BLACK 4
36 F11790 HEATER, TUNNEL, COVER, BLUE GRANITE 1
37 B11779 STUB, 12-3 SJTW YELLOW 1
38 B00191 NYLON TIE, 11IN BLACK 4
39 C00293 #8 X .5IN PAN, BLACK SMS, PHILLIPS 2
40 B00192 TIE HOLDER WITH GLUE 1
41 B11606 STRAIN RELIEF, PIGTAIL 1
42 H03545 COVER, SERIAL # LABEL 1
43 H00565-5 LABEL, SERIAL NUMBER 1
44 C02305 CAP NUT, .5 IN, PUSH-ON 2
45 C00240 WASHER, SHOULDER, NYLON 4
46 G11767 WHEEL, 10 IN 1
47 D11170 AXLE 1
48 F11789 BASE 1
49 C00314-1 HEX BOLT, 1-4 X 20 X 1 IN 8
50 G03518 CASTER, 4 IN 2
51 J00632-1 PULSE HOSE, PUMP-QD, 42 IN 2
52 A13140 CAP, FPT, .375 BRASS 1
53 G13132 PUMP, 200PSI, 120V 1
54 B00190 NYLON TIE, 4 IN 13
55 J11508 SCREW CLAMP #6, .43 TO .875 IN 6
56 D13103 PLATE, PUMP, GALAXY, FLAT 1
57 H02564-2 LABEL, CAUTION, MOTOR HOUSING 1
58 J11933 HOSE, .5 IN POLYWIRE, 20 IN 1
59 K11935 STRAINER, INLINE, .5 IN 1
60 J11933 HOSE, .5IN POLYWIRE, 33 IN 1
61 J11154 SOLUTION HOSE, .375, 100 PSI, WIRE IN LG 1
62 J00618 VACUUM HOSE, 2 IN GREY, WIRE, 7 IN LG 1
63 E11169 GASKET, VAC MOTOR, GALAXY 2
64 B00179-2 CLOSED END CNTR, 16-3 4
00580-13IN-MF-A