TRUE RESIDENTIAL
®
TEC_TM_102 REV. B
02/02/2022
Page 46 of 74
C A B I N E T S E T U P
Follow the instructions below to install drawer overlay
panels. For custom panel specifications, please see
“Custom Overlay Panel Specifications” starting on
page 25.
REQUIRED TOOLS
Required tools include (but may not be limited to)
the following:
• Surface protection*
• Phillips bit driver
• 2+ Clamps >/= 2" (51 mm)
• 1/8" Drill Bit
• (Qty 8) #6 x >1/2" Screws**
• (Qty 3) #6 x 1/2" Screws**
• Drill
*Cardboard, moving blanket, foam padding, etc.
** Screw type varies by panel material. Screws going through
the drawer front (rather than the drawer skin bracket) must
be 1/2” (13 mm) + Overlay Panel Thickness long.
PROCEDURE
1. Carefully lay the drawer overlay panel on a
protected surface.
2. With a Phillips bit driver, remove the drawer front
assembly. See fig. 1.
3. If present, remove the drawer skin from the drawer
front. See fig. 2.
NOTE: DO NOT REMOVE THE DR AWER
BR ACK ETS FROM THE DR AWER FRONT.
4. Remove the drawer gasket. See fig. 3.
5. With a 1/8" drill bit, carefully drill pilot holes in the
drawer front. See figs. 4a and 4b.
6. If so desired, attach a drawer handle to the overlay
panel.
7. Place the drawer front face down on the overlay
panel. Align the drawer front and panel edges.
See fig. 5.
NOTE: BE SURE THE OVERL AY PANEL IS
CORRECTLY ORIENTED BEFORE INSTALLING
ON THE DR AWER FRONT. SEE FIG. 6.
8. Clamp the drawer front and panel together.
See fig. 5.
NOTE: IF THE CL AMP JAWS ARE NOT
PADDED, INSERT PADDING BET WEEN THE
CL AMP AND THE OVERL AY TO PROTECT
THE PANEL’S FINISH.
9. Fasten the overlay panel to the drawer front. Then,
remove the clamps. See fig. 7.
10. Install the drawer gasket. Verify the gasket is fully
seated in the gasket channel. See fig. 8.
11. Install the drawer assembly.
12. Verify the drawer closes correctly and the gasket
seals without gaps (see fig. 9). Adjust the drawer
as needed; see “Drawer Adjustment” (page 66).
DR AWER OVERL AY PANEL INS TALL ATION
FIG. 1.
Drawer front assembly screw locations. Other side not shown.
FIG. 2.
Remove the indicated drawer skin bracket screws.
Summary of Contents for RESIDENTIAL ADA HEIGHT TUBADA-24-R/L-RG-A-S
