background image

 

        

 

Assembly Instructions

 

IMPORTANT SAFETY INSTRUCTIONS 

 

 

 
Basic Guidelines for Setting Up Your Treadmill 

After removing the treadmill from the packaging, place your treadmill on a clean, level surface. Make 
sure the electrical cord easily reaches a grounded three-pronged outlet and has enough slack to allow 
the deck to incline without tightening the cord. Do not allow the treadmill assembly to rest on the cord. 

 
Important Electrical Requirements 

– 120V 

Your TRUE treadmill requires a dedicated 120 volt, alternating current (AC), 20 amp grounded outlet 
circuit. This means nothing else can be plugged into the same circuit. Most power circuits are rated for 
this 120V AC 20 amp requirement, but you must ensure the treadmill does not share the circuit with 
anything else. 
 

Important Electrical Requirements 

– 220V 

Your TRUE treadmill requires a dedicated 220 volt, alternating current (AC), 10 amp grounded outlet 
circuit. This means nothing else can be plugged into the same circuit. Most power circuits are rated for 
this 220V AC 10 amp requirement, but you must ensure the treadmill does not share the circuit with 
anything else. 
 

Danger: Do not use an extension cord or ungrounded outlet. 

The ground helps prevent electrical damage to your treadmill and enhances your safety by helping to 
prevent shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the 
treadmill is properly grounded. Do not modify the plug provided with the treadmill if it will not fit the 
outlet. Have a proper outlet installed by a qualified electrician. 

 

 

 
Should you need technical assistance in assembly of your Mobility Research Fitness 
product, contact Mobility Research Technical Support at 1-800-332-9255 (USA) or 

[email protected]

 

 

 

 

Read and understand all instructions and warnings prior to use. 

  Obtain a medical exam before beginning any exercise program. If at any time 

during exercise you feel faint, dizzy, or experience pain, stop, consult a physician. 

  Obtain proper instruction prior to use. 

  This treadmill is intended for light commercial use only. 

  Inspect the treadmill for incorrect, worn, or loose components and do not use until 

corrected, replaced, or tightened prior to use. 

  Do not wear loose or dangling clothing while using the treadmill. 

  Care should be used when mounting or dismounting the treadmill. 

  Read, understand, and test the emergency stop procedures before use. 

  Disconnect all power before servicing the treadmill. 

  Do not exceed maximum user weight of 350 lbs. 

  Keep the top side of the moving surface clean and dry. 

  Keep children and animals away. 

  Use caution when moving and assembling treadmill. 

  All exercise equipment is potentially hazardous. If attention is not paid to the 

conditions of equipment usage, death, or serious injury could occur. 

Summary of Contents for GK2200T



















Reviews: