True Manufacturing Company TMW TMW-36F Installation Manual Download Page 3

............ www.truemfg.com ............

True Food Service Equipment, Inc.

1

1

SAFETY INFORMATION

•  This freezer must be properly installed and located in 

accordance with the Installation Instructions before 
it is used.

•  Do not allow children to climb, stand or hang on 

the shelves in the freezer.  They could damage the 
freezer and seriously injure themselves.

•  Do not touch the cold surfaces in the refrigerated 

compartment when hands are damp or wet.  Skin 
may stick to these extremely cold surfaces.

•  Do not store or use fammable liquids or vapours in 

the vicinity of  this or any other appliance.

•  Keep fingers out of  the “pinch point” areas; 

clearances between the doors and between the doors 
and cabinet are necessarily small; be    careful closing 
doors when children are in the area.

NOTE: Any servicing, warranty repairs or maintenance 
should be carried out by qualified personnel, failure 
to do so could be dangerous and may invalidate your 
warranty.

•  Unplug the freezer before cleaning and    

 

 making 

repairs.

•  Setting temperature controls to 0 position does 

not isolate the unit from the electrical supply, you 
must disconnect the main power lead from the wall 
receptacle to isolate.

WARNING!

Use this appliance for its intended purpose as described in this Owner Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

How to Maintain Your              Unit 

to Receive the Most Efficient and 

Successful Operation

You have selected one of the finest commercial freezer units made.  It is manufactured under 

strict quality controls with only the best quality materials available.  Your TRUE freezer, when 

properly maintained, will give you many years of trouble-free service.

Summary of Contents for TMW TMW-36F














Reviews: