True Manufacturing Company TGU-2 Installation Manual Download Page 16

............ www.truemfg.com ............

True Food International Equipment, Inc.

14

14

SETTING TIME OF DAY

LAE Electronic Control

Info/Set Point 

Button

Manual Defrost/ 

Down Button

Manual Activation/ 

Up Button

Stand-By

Button

Compressor 

Running

Activation of 2nd  

Parameter Set - NA

Alarm - NA

Cabinet in Defrost

Evaporator Fan 

Running

LAE Control Icons

May need to unlock control. Does not adjust for daylight savings time.

WHY:
TO MAKE SURE THE CABINET DOES NOT INITIATE  

DEFROST & GET WARM DURING TIMES OF HIGH USAGE.
Control is designed to initiate defrost at specific times of 

the day.

HOW:
A.

  To change the time of day, press and release the info 

button         . “T1” will appear.
Press and release the up button          until “min” 

appears. See image 1.

B.

  While pressing and holding the info button         , press 

the up           or down          button to change the clock 

minutes. See image 2.

C.

  Once the minutes have been set correctly, release the 

info button          and “hrs” will appear on the display. 

See image 3.

D.

  While pressing and holding the info button         , press 

the up          or down          button to change the clock 

hours. See image 4.

Note:

 

When changing the clock hour, the clock will be 

displayed in 24 hour format ranging from 0-23. 

E.

  Once the hour has been set correctly, release the info 

button         .
Wait 5 seconds for the display to show temperature.  

See image 5.

1

2

3

4

5

Summary of Contents for TGU-2

























Reviews: