background image

............ www.truemfg.com ............

INSTA LLATION MANUA L FOR TGU MODELS 

(TRUE GASTRONORM UNDERCOUNTER & WORKTOP 

REFRIGER ATORS / FREEZERS)

TRUE GASTRONORM         

UNDERCOUNTER  &  WORKTOP       

REFRIGER ATORS / FREEZERS

CONGRATULATIONS!   

You have just purchased the finest commercial 

refrigeration available. You can expect many years 

of trouble-free operation.

TABLE OF CONTENTS

Safety Information

Safety Precautions  _______________________1

Proper Disposal __________________________2

Connecting Electricity _____________________3
Adapter Plugs  ___________________________3

Installation / Operation Instructions

Ownership  ______________________________4

Required Tools   __________________________4

Uncrating & Locating  _____________________4

Installation of Leg/Castors   ________________5 

Leveling Cabinet  _________________________6

Electrical Instructions _____________________6

Start-up _________________________________7

Shelving Installation - Operation  ___________8
LAE Electronic Control ____________________9-18

Maintenance, Care & Cleaning

Cleaning Condenser Coil   _________________19
Stainless Steel Equipment Care & Cleaning __20

TGU-2

TGU-3F

6/15/11 AN #912630

*Spanish, German, French, and Dutch versions included.

COLD INNOVATIONS 

®

TRUE EUROPE • Fields End Road • Goldthorpe • NR, Rotherham • South Yorkshire UK

UK Office/Tec44 (0) 1709 888 888 • UK Free Phone 0800 783 2049

UK Free Phone from France, Germany, Netherlands, Belgium & Republic of Ireland 00-880-8783-4685

TRUE FOOD INTERNATIONAL, INC. • 2001 East Terra Lane • O’Fallon • Missouri • 63366-4434 • USA

USA Office/Technical (001) 636-240-2400 • Email [email protected]

Summary of Contents for TGU-2

























Reviews: