background image

120mm

Top view

Side View 

40mm

40mm

RUDDER

Air tank

Switch

Air inlet

     3-way

pressure inlet

     3-way

pressure inlet

     3-way

pressure inlet

The status when the

gear up 

Pull out length of 8mm 

to make gear down 

Air valve

Air valve

Make sure to assemble retracts as instructed below.

Two wheel retract system

Quick release connector  

Quick release connector  

Pressure reduction inlet  

Strut 

Strut 

3-way pressure inlet

3

Pressure reduction inlet

1

1

Air tank

1

Air inlet

2

1
1

Air line (3000mm)

2

Quick release connector  

Strut( 90 ) 

Switch

Clevis

Rod (2X300mm)

1
1

1

Retainer

TP Screw(2x14mm) 2

Ø1.7mm

Ø0.2mm

Pleas notice the inner diameter 

of eachside the pressure reduction inlet. 

Please insure the sealing of theretract 

system before flight .

o

Adjustment.

The centre of the Gravity.

71

14

70

Specifications: 

Wing Span:               1840mm (72 ½” Inches)

Length:                      1625mm(64in)

Wing Area:                946sq.in

Wing loading:           33oz/sq.ft

Flying weight:           13 Ibs

 Power: ..91 _ 1.20 Two Stroke or .90 - .120 Four Stroke

Radio: 6 Channel w/8 Standard Servos 

SPITFIRE MK.XIV\XIX

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building 

experience.If misused or abused,it can cause serious bodily injury 

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your 

airplane before its first flight.Please carefully read and follow all 

instructions included with this airplane,your radio control system 

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not  a toy!

Summary of Contents for SPITFIRE MK.XIV









Reviews: