background image

6

s

ectiOn

 2 — i

MpOrtant

 s

afe

 O

peratiOn

 p

ractices

Periodically check to make sure the blades come to 

3. 

complete stop within approximately (5) five seconds after 

operating the blade disengagement control. If the blades 

do not stop within the this time frame, your machine 

should be serviced professionally by an authorized MTD 

Service Dealer.
Check brake operation frequently as it is subjected to wear 

4. 

during normal operation. Adjust and service as required.
Check the blade(s) and engine mounting bolts at frequent 

5. 

intervals for proper tightness. Also, visually inspect blade(s) 

for damage (e.g., excessive wear, bent, cracked).   Replace 

the blade(s) with the original equipment manufacturer’s 

(O.E.M.) blade(s) only, listed in this manual. “Use of parts 

which do not meet the original equipment specifications 

may lead to improper performance and compromise 

safety!” 

Mower blades are sharp. Wrap the blade or wear gloves, 

6. 

and use extra caution when servicing them.
Keep all nuts, bolts, and screws tight to be sure the 

7. 

equipment is in safe working condition. 
Never tamper with the safety interlock system or other 

8. 

safety devices. Check their proper operation regularly.
After striking a foreign object, stop the engine, disconnect 

9. 

the spark plug wire(s) and ground against the engine. 

Thoroughly inspect the machine for any damage. Repair 

the damage before starting and operating.
Never attempt to make adjustments or repairs to the 

10. 

machine while the engine is running.
Grass catcher components and the discharge cover are 

11. 

subject to wear and damage which could expose moving 

parts or allow objects to be thrown. For safety protection, 

frequently check components and replace immediately 

with original equipment manufacturer’s (O.E.M.) parts only, 

listed in this manual. “Use of parts which do not meet the 

original equipment specifications may lead to improper 

performance and compromise safety!”

Do not change the engine governor settings or over-speed 

12. 

the engine. The governor controls the maximum safe 

operating speed of the engine. 
Maintain or replace safety and instruction labels, as 

13. 

necessary. 

Observe proper disposal laws and regulations for gas, oil, 

14. 

etc. to protect the environment.

According to the Consumer Products Safety Commission 

15. 

(CPSC) and the U.S. Environmental Protection Agency (EPA), 

this product has an 

Average Useful Life

 of seven (7) years, 

or 270 hours of operation. At the end of the 

Average Useful 

Life

 have the machine inspected annually by an authorized 

service dealer to ensure that all mechanical and safety 

systems are working properly and not worn excessively. 

Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any 

way. Tampering with the governor setting can lead to a runaway 

engine and cause it to operate at unsafe speeds. Never tamper 

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal 

EPA emission regulations for SORE (Small Off Road Equipment) 

are certified to operate on regular unleaded gasoline, and 

may include the following emission control systems: Engine 

Modification (EM), Oxidizing Catalyst (OC), Secondary Air 

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! 

This machine is equipped with an 

internal combustion engine and should not be used 

on or near any unimproved forest-covered, 

brushcovered or grass-covered land unless the 

engine’s exhaust system is equipped with a spark 

arrestor meeting applicable local or state laws (if 

any).

If a spark arrestor is used, it should be maintained in effective 

working order by the operator. In the State of California the 

above is required by law (Section 4442 of the California Public 

Resources Code). Other states may have similar laws. Federal laws 

apply on federal lands. 

A spark arrestor for the muffler is available through your 

nearest engine authorized service dealer or contact the service 

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

WARNING!

 

Your Responsibility—Restrict the use of this power machine to persons who read, understand and 

follow the warnings and instructions in this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Summary of Contents for TB2450





































Reviews: