background image

23

IMPORTANT:

 If removing the battery for any reason, 

disconnect the NEGATIVE (Black) wire from it’s 
terminal first, followed by the POSITIVE (Red) wire. 
When re-installing the battery, always connect the 
POSITIVE (Red) wire its terminal first, followed by the 
NEGATIVE (Black) wire. Be certain that the wires are 
connected to the correct terminals; reversing them 
could change the polarity and cause damage to your 
engine’s alternating system.

Charging

If the unit has not been put into use for an extended 
period of time, charge the battery with an automotive-
type 12-volt charger for a minimum of one hour at six 
amps.

WARNING: 

Batteries give off an explosive

gas while charging. Charge battery in a well
ventilated area and keep away from an open
flame or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas
appliances.

Fuses

Two fuses are installed in your tractor’s wiring harness 
to protect the tractor’s electrical system from damage 
caused by excessive amperage. 

If the electrical system does not function, or your 
tractor’s engine will not crank, first check to be certain 
that the fuse has not blown. 

One can be found under the hood mounted behind the 
top of the dash panel on the support bar. The other can 
be found under the seat mounted to the inside of the 
tractor frame next to the battery tray. Pull the fuse out 
and inspect it to determine if it is good or blown.

IMPORTANT:

 Always use a fuse with the same 

amperage capacity for replacement. 

SECTION 9:  OFF-SEASON STORAGE

Clean and lubricate the tractor as instructed in 

Section 7: 

MAINTAINING YOUR LAWN TRACTOR

 on page 17 of this 

manual before storing for an extended period.

WARNING: 

Drain fuel only into an

approved container outdoors, away from an
open flame. Allow engine to cool. Extinguish
cigarettes, cigars, pipes, and other sources of
ignition prior to draining fuel.

Follow the instructions in the 

Service, Storage & 

Specifications

 section of the 

Briggs & Stratton

 

Operator/Owner Manual for proper engine care prior to 
storing your tractor.

WARNING: 

Never store the machine or

fuel container indoors where there is an open
flame, spark or pilot light such as on water
heater, furnace, clothes dryer or other gas
appliance.

SECTION 10:  ATTACHMENTS & ACCESSORIES

The following attachments and accessories are compatible for 

Lawn

 

Tractor Model D609G & G609G

. See the 

retailer from which you purchased your tractor, an authorized 

MTD

 Service Dealer or phone (800) 800-7310 for 

information regarding price and availability.

NOTE: 

Lawn tractor models D609G and G609G are NOT designed for use with any type of ground-engaging

attachments (e.g. tiller or plow). Use of this type of equipment WILL void the tractor’s warranty.

MODEL

DESCRIPTION

OEM-190-116

42-inch Deck Mulch Kit

OEM-190-601

FastAttach™ Twin Bagger Grass Collector

OEM-190-603

FastAttach™ Grille Guard (mounts on front of tractor)

OEM-190-604

FastAttach™ Yard-Mate™ Storage Container/Toolbox (mounts on rear of tractor)

OEM-190-607

FastAttach™ Deluxe Tractor Sunshade

OEM-190-822

FastAttach™ 46-inch Front Dozer Blade

OEM-190-823

FastAttach™ 42-inch Two-stage Snow Thrower

Summary of Contents for D609G









































Reviews: