background image

The limited warranty set forth below is given by Troy-Bilt LLC with respect 
to new merchandise purchased and used in the United States and/or its 
territories and possessions, and by MTD Products Limited with respect to 
new merchandise purchased and used in Canada and/or its territories and 
possessions (either entity respectively, “Troy-Bilt”).
“Troy-Bilt” warrants this product (excluding its normal wear parts as 
described below) against defects in material and workmanship for a 
period of two (2) years commencing on the date of original purchase and 
will, at its option, repair or replace, free of charge, any part found to be 
defective in materials or workmanship. This limited warranty shall only 
apply if this product has been operated and maintained in accordance 
with the Operator’s Manual furnished with the product, and has not been 
subject to misuse, abuse, commercial use, neglect, accident, improper 
maintenance, alteration, vandalism, theft, fire, water, or damage because 
of other peril or natural disaster. Damage resulting from the installation or 
use of any part, accessory or attachment not approved by Troy-Bilt for use 
with the product(s) covered by this manual will void your warranty as to any 
resulting damage.
Normal wear parts are warranted to be free from defects in material and 
workmanship for a period of thirty (30) days from the date of purchase. 
Normal wear parts include, but are not limited to items such as: batteries, 
belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow 
thrower skid shoes, friction wheels, shave plates, auger spiral rubber and 
tires.

HOW TO OBTAIN SERVICE: 

Warranty service is available, WITH PROOF 

OF PURCHASE, through your local authorized service dealer. To locate 
the dealer in your area:

In the U.S.A.

Check your Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131, 
Cleveland, Ohio 44136-0019, or call 1-866-840-6483 or 1-330-558-7220, 
or log on to our Web site at www.troybilt.com.

In Canada

Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-668-
1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does

 not 

provide coverage in the following cases:

a. 

The engine or component parts thereof. These items may 
carry a separate manufacturer’s warranty. Refer to applicable 
manufacturer’s warranty for terms and conditions.

b. 

Log splitter pumps, valves, and cylinders have a separate one- 
year warranty.

c. 

Routine maintenance items such as lubricants, filters, blade 
sharpening, tune-ups, brake adjustments, clutch  adjustments, 

deck adjustments, and normal deterioration of the exterior finish 
due to use or exposure.

d. 

Service completed by someone other than an authorized service 
dealer.

e. 

Troy-Bilt does not extend any warranty for products sold or  
exported outside of the United States and/or Canada, and 
their respective possessions and territories, except those sold 
through Troy-Bilt’s authorized channels of export distribution.

f. 

Replacement parts that are not genuine Troy-Bilt parts.

g. 

Transportation charges and service calls.

h. 

If Products are used commercially. (Troy-Bilt may separately 
offer Limited Commercial Warranties on certain select products. 
Ask your dealer or retailer for details or contact Troy-Bilt Service 
for more information).

No implied warranty, including any implied warranty of merchant-
ability of fitness for a particular purpose, applies after the applicable 
period of express written warranty above as to the parts as identi-
fied. No other express warranty, whether written or oral, except as 
mentioned above, given by any person or entity, including a dealer or 
retailer, with respect to any product, shall bind Troy-Bilt. During the 
period of the warranty, the exclusive remedy is repair or replacement 
of the product as set forth above.
The provisions as set forth in this warranty provide the sole and 
exclusive remedy arising from the sale. Troy-Bilt shall not be liable 
for incidental or consequential loss or damage including, without 
limitation, expenses incurred for substitute or replacement lawn care 
services or for rental expenses to temporarily replace a warranted 
product.

Some states do not allow the exclusion or limitation of incidental or 
consequential damages, or limitations on how long an implied warranty 
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the 
purchase price of the product sold. 

Alteration of safety features of the 

product shall void this warranty.

 You assume the risk and liability for 

loss, damage, or injury to you and your property and/or to others and their 
property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original 
purchaser or to the person for whom it was purchased as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: 

 This limited war-

ranty gives you specific legal rights, and you may also have other rights 
which vary from state to state.

IMPORTANT:  

Owner must present Original Proof of Purchase to obtain 

warranty coverage.

Troy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-70 

MTD Canada Limited - KITCHENER, ON NG 4J1; Phone 1-800-668-138

MANUFACTURER’S LIMITED WARRANTY FOR

Summary of Contents for 31AH9Q77766

































Reviews: