background image

4

S

ection

 2 — i

mportant

 S

afe

 o

peration

 p

racticeS

4. 

Check bolts and screws for proper tightness 

at frequent intervals to keep the machine in 

safe working condition. Also, visually inspect 

machine for any damage. 

5. 

Before cleaning, repairing or inspecting, stop 

the engine and make certain the tines and 

all moving parts have stopped. Disconnect 

the spark plug wire and ground it against the 

engine to prevent unintended starting.

6. 

Do not change the engine governor settings 

or over-speed the engine. The governor 

controls the maximum safe operating speed 

of the engine.

7. 

Maintain or replace safety and instruction 

labels, as necessary.

8. 

Follow this manual for safe loading, 

unloading, transporting and storage of this 

machine.

9. 

Always refer to the Operator’s Manual for 

important details if the machine is to be 

stored for an extended period.

10. 

If the fuel tank has to be drained, do this 

outdoors.

11. 

Observe proper disposal laws and regulations 

for gas, oil, etc. to protect the environment.

12. 

According to the Consumer Products 

Safety Commission (CPSC) and the U.S. 

Environmental Protection Agency (EPA), 

this product has an 

Average Useful Life

 of 

seven (7) years, or 130 hours of operation. At 

the end of the 

Average Useful Life

 have the 

machine inspected annually by an authorized 

service dealer to ensure that all mechanical 

and safety systems are working properly and 

not worn excessively. Failure to do so can 

result in accidents, injuries or death.

Notice Regarding Emissions

Engines which are certified to comply with 

California and Federal EPA emission regulations 

for SORE (Small Off Road Equipment) are certified 

to operate on regular unleaded gasoline, and may 

include the following emission control systems: 

Engine Modification (EM), Oxidizing Catalyst (OC), 

Secondary Air Injection (SAI) and Three Way Catalyst 

(TWC) if so equipped.

Spark Arrestor

WARNING!

 

This machine is equipped 

with an internal combustion engine and 

should not be used on or near any 

unimproved forest-covered, brush-

covered or grass-covered land unless the 

engine’s exhaust system is equipped 

with a spark arrestor meeting applicable 

local or state laws (if any).

If a spark arrestor is used, it should be maintained in 

effective working order by the operator. In the State 

of California the above is required by law (Section 

4442 of the California Public Resources Code). Other 

states may have similar laws. Federal laws apply on 

federal lands.
A spark arrestor for the muffler is available through 

your nearest engine authorized service dealer or 

contact the service department, P.O. Box 361131 

Cleveland, Ohio 44136-0019.

19. 

If the machine should start making an 

unusual noise or vibration, stop the engine, 

disconnect the spark plug wire and ground 

it against the engine. Inspect thoroughly for 

damage. Repair any damage before starting 

and operating.

20. 

Keep all shields, guards and safety devices in 

place and operating properly.

21. 

Never pick up or carry machine while the 

engine is running.

22. 

Powered walk-behind tiller work is strenuous. 

You must be in good physical condition and 

mentally alert. If you have any condition that 

might be aggravated by strenuous work, 

check with your doctor before operating a 

powered walk-behind tiller.

23. 

Use only attachments and accessories 

approved by the manufacturer. Failure to do 

so can result in personal injury.

24. 

If situations occur which are not covered in 

this manual, use care and good judgement. 

Contact Customer Support for assistance and 

the name of you nearest servicing dealer.

Maintenance & Storage

1. 

Keep machine, attachments and accessories 

in safe working order.

2. 

Never store the machine with fuel in the fuel 

tank inside a building where ignition sources 

are present, such as hot water and space 

heaters, clothes dryers, etc.

3. 

Allow machine to cool at least five minutes 

before storing. Never tamper with safety 

devices. Check their proper operation 

regularly.

Safety Symbols

This page depicts and describes safety symbols that may appear on this product.  Read, understand and follow all instructions on the machine before attempting to 

assemble and operate.

Symbol

Description

READ THE OPERATOR’S MANUAL(S)

 

Read, understand and follow all instructions in the manual(s) before attempting to assemble and operate

WARNING— ROTATING TINES

 

Do not put hands or feet near rotating parts. Contact with the rotating parts can amputate hands and feet.

WARNING!

 

Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the warnings and 

instructions in this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Summary of Contents for 21AE682W766





























Reviews: