8
EN
fan heater TFC 220 E
Setting the operating mode
The device comes with the following operating modes:
•
Comfort mode
•
Night mode
•
Eco mode
•
Frost monitor function
Please proceed as follows to activate the desired operating
mode:
ü
The device is switched on.
1. Press the
power
button (19).
ð
The display shines brightly and the control panel is
activated.
2. Repeatedly press the
mode
button (18) until the icon for
the desired operating mode (9, 10, 11 or 12) is displayed.
ð
The device starts in the desired operating mode.
Comfort mode
The device automatically operates at the high heating level until
the determined room temperature exceeds the desired room
temperature by 2 °C. Then the heating switches off.
The
heating
indication (20) is no longer displayed.
The
comfort mode
indication (9) continues to be displayed.
If the determined room temperature falls below the desired
room temperature by 2 °C, the heating switches back to
operation at the high heating level.
Night mode
The device automatically operates at the low heating level until
the determined room temperature exceeds the desired room
temperature by 2 °C. Then the heating switches off.
The
heating
indication (20) is no longer displayed.
The
night mode
indication (10) continues to be displayed.
If the determined room temperature falls below the desired
room temperature by 2 °C, the heating switches back to
operation at the low heating level.
Eco mode
The device automatically operates at the high heating level
when the room temperature is below 16 °C.
The device automatically operates at the low heating level when
the room temperature is above 18 °C.
The device switches off automatically when the room
temperature is above 21 °C. This temperature cannot be
changed.
Frost monitor function
This function is only available in standby mode. The devices
heats automatically when the room temperature is below 5 °C
and switches off when the temperature exceeds 7 °C. These
temperatures cannot be changed.
Setting the desired room temperature
The determined room temperature is displayed in the
temperature
indication (23). You can adjust the desired room
temperature in comfort mode and in night mode.
1. Press the
temperature
button (14).
ð
The
temperature
indication (23) flashes.
ð
The desired room temperature is displayed.
2. Press the arrow buttons
increase value
(16) or
decrease
value
(17) to adjust the desired room temperature. Setting
is possible in the range between 15 °C and 35 °C in
increments of 1 °C.
ð
The desired room temperature is saved and displayed in
the
temperature
indication (23) for approx. 5 seconds.
Then the current room temperature is displayed again.
Info
The desired room temperature should be higher than
the current room temperature.
Setting the timer
The timer has the following modes of operation:
•
automatic switch-on upon expiry of a preset number of
hours and minutes
•
automatic switch-off upon expiry of a preset number of
hours and minutes
The setting range for the timer spans from 1 minute to 24 hours
and can be adjusted in increments of 1 minute.
Note
Do not leave the operating device unattended in a
freely accessible room with an activated timer.
Automatic switch-on
ü
The device is set to the
frost monitor function
.
1. Press the
timer
button (15).
2. Select the desired number of hours and minutes by use of
the
increase value
(16) or
decrease value
(17) arrow
button. The value range is between 1 minute and 24 hours.
ð
The number of hours and minutes flashes on the
hours /
minutes
indication (22).
3. Press the
timer
button (15).
ð
The desired time until automatic switch-on is saved.
ð
The
timer
indication (8) is displayed.
ð
The time left until switch-on is displayed in the
hours /
minutes
indication (22) and counted down.
ð
Once the set time has elapsed, the device will switch
over into
comfort mode
.
Notes regarding automatic switch-on:
•
Manually switching the device on disables the automatic
switch-on function.
•
If you select 0 hours / minutes, the timer will be off.