background image

0063

LIODSCSCE-Rev. 15617

Print: LIODSCSCE-5c-04/19_r1-11/19 (CDS)

DSCS-9/10 Series 

Manual

Detroit Radiant Products Company 

Installation, Operation, 

Maintenance, and Parts

INSTALLER: Present this manual to the end user.

Keep these instructions in a clean and dry place for future reference.

Model#:

 ___________________

Serial #:

 _________________________

(located on rating label)

This heater 

must be installed and serviced by a Gas Safe Registered Gas Engineer 

only!  Conversion of the heater for use with other gases must be carried out by a Gas 
Safe Registered Gas Engineer. Read these instructions carefully before attempting to 
install, operate, or service the heater.

Storage of petrol and other flammable vapors and liquids in the vicinity of this or any 
other appliance may result in fire or explosion. Do not store or use petrol or other 
flammable vapors and liquids in the vicinity of this or any other appliance.  Maintain 
clearances to combustibles at all times.

This heater is not approved for use in indoor residential applications 

and must 

never be install indoor in the home. This heater may only be used in outdoor residential 
applications or indoor/outdoor commercial or industrial applications.  Installation in 
residential indoor spaces may result in property damage, asphyxiation, serious injury, 
or death.

Failure to comply with these warnings and instructions, and those on the heater, could 
result in personal injury or death.

WARNING

!

WARNING

!

If you smell gas:

 

•  Shut off gas to the appliance.  

• Call your gas supplier. Do not use any phone in your building. 

•  Extinguish any open flame.  

• Follow the gas supplier’s instructions. 

•  Do not try to light any appliance. 

• If you cannot reach your gas supplier, call the fire department.

•  Do not touch any electrical switch.  

For Your Safety

Summary of Contents for DSCS-10 Series

































Reviews: