Trotec PWLS 10-150 Operating Manual Download Page 6

6

EN

LED construction site spotlight PWLS 10-150

Start-up

Unpacking the device

Take the device out of the packaging.

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Check the contents for completeness and look for
damages.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Dispose of the packaging material according to the
national regulations.

Putting the device into operation

Warning of hot surface

Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!

Warning of electrical voltage

Do not touch the device's power cable or power cable
connection with wet or damp hands.

Warning of electrical voltage

Do not touch the device's power cable or power cable
connection with wet or damp hands.

Warning

Do not look directly into the LEDs! The optical radiation
can be harmful for your eyes.

Adjusting the lighting position

Please proceed as follows to adjust the lighting position:

1. If necessary, switch the device off by setting the on/off

switch (7) to position 

O

.

2. Allow the device to cool down and remove the mains plug

from the mains socket.

3. Loosen the locking screw (3) on both sides of the device by

turning in counter-clockwise direction.

4. Rotate the surface LED (2) to the desired position.

2

3

5. Tighten the locking screw (3) on both sides of the device.
6. Loosen the surface LED (2) together with the outer frame

by turning the central locking screw (5) in counter-
clockwise direction.

ð

You can now rotate the surface LED (2) together with
the frame in both directions.

2

5

Info

The transport handle of the LED construction site
spotlight and the surface LED can be rotated by up 
to 360°.

7. Lock the new position of the surface LED (2) by turning the

central locking screw (5) in clockwise direction.

Summary of Contents for PWLS 10-150










Reviews: