EN
7
LED work lamp PWLS 05-10 / PWLS 06-10
1. Open the battery compartment (6) by removing the battery
compartment cover (5).
2. Insert the batteries with correct polarity into the battery
compartment (6) (+/-).
3. Close the battery compartment (6) by closing it with the
battery compartment cover (5).
ð
The device
PWLS 05-10
is now ready to use.
Charging batteries for PWLS 06-10
Note
The battery can be damaged in case of improper
charging.
Pull out the USB charging cable (13) from the external
charger each time before switching the device on.
Never charge the battery at ambient temperatures
below -20 °C or above 55 °C.
Charge the battery of
PWLS 06-10
completely before using the
device. Use the USB charging cable (13) and a standard
charger.
Proceed as follows to charge the battery:
1. Open the cover (10) of the USB connections at the back of
the cordless work light.
2. If applicable, plug the charger into the mains socket.
3. Put the USB charging cable (13) into the USB connection/
input (9) of the device
PWLS 06-10
and into a charger.
ð
When the battery status is very low, the charging time is
6-7 hours.
ð
When the battery is charged 25%, the first LED of the
battery indication (12) is illuminated in blue. When the
battery is charged 50 %, the second LED of the battery
indication (12) is illuminated in blue. When the battery is
charged 75 %, the third LED of the battery
indication (12) is illuminated in blue.
ð
When the battery is charged 100 %, the fourth LED of
the battery indication (12) is illuminated in blue.
4. When all LEDs of the battery indication (12) are illuminated
and the battery is completely charged, you can remove the
USB charging cable (13) from the charger and from the
device
PWLS 06-10
.
5. Pull the charger out of the mains socket.
ð
The LED work light and the charger may have become
warm during charging. Let the LED work light and the
charger cool down to room temperature.
ð
The device
PWLS 06-10
is now ready to use.
Note
Note that the battery status of the device PWLS 06-10
cannot be read while in operation. You can only read
the battery status while charging.
Operation
Tips and notes on handling the LED work light
General information:
•
Avoid looking directly into the light source.
•
Use the devices only for a temporary illumination of indoor
and outdoor areas, e.g. for construction sites.
•
The devices
PWLS 05-10
and
PWLS 06-10
can be used as
strobe.
•
The LED work lights are particularly suited for illuminating
larger areas.
Info
You can turn the handles of the LED work lights by
180° and set 6 positions.
Switching the device on and off
Switching the devices PWLS 05-10 and PWLS 06-10 on and off
works identically.
1. Press the on/off switch (3/7) 1 x to switch the device on or
off.
ð
Once the device is switched on, the surface LED (1) is
illuminated.
ð
Once the device is switched off, the surface LED (1) is
not illuminated.
Setting brightness level and strobe mode
Setting brightness level and strobe mode works identically for
both devices
PWLS 05-10
and
PWLS 06-10
ü
Check whether the batteries (standard or integrated) are
completely charged. If necessary, replace the batteries or
charge the integrated battery.
1. Set the lowest light intensity by pressing the on/off
switch (3/7) 1 x.
2. Set the high brightness level by pressing the on/off
switch (3/7) 3 x.
3. Set the strobe mode by pressing the on/off
switch (3/7) 5 x.
Always proceed in the same order to set the desired light
intensity or the strobe mode.
Note
By quickly pressing the
on/off switch (3/7), you can switch between the
brightness levels and the strobe mode.
Using the power bank
If you like to use the device
PWLS 06-10
as power bank,
proceed as follows:
1. Put the USB charging cable (13) into the USB connection/
output (8) of the device PWLS 06-10.
2. Then plug the USB charging cable into the USB input of the
device that you would like to charge.
3. Charge your device until it has reached the desired
charging status.
