background image

EN

18

oil heater IDX 30 D

No. Spare part

No. Spare part

No. Spare part

1

Combustion Chamber Assembly

5.8

Sealing gasket

19

Cord Bushing

2

Upper Shell

5.9

Airout Filter

20

Seal Ring

3

Burner Head Assembly

5.10 End Filter Cover

21

Water Drain Screw

3.1

Nozzle Kit

5.11 Pressure Gauge

22

PCB Bracket

3.2

Nozzle Seal Spring

5.12 Air Inlet Filter

23

Room Sensor

3.3

Nozzle Seal Washer

5.13 Adjusting Screw

24

Fuse

3.4

Nozzle Sleeve

5.14 Spring

25

Main PCB Assembly

3.5

Burner Head

5.15 Ball

26

Thermostat Control Knob

3.6

Air Line Fitting

6

Fan Guard

27

Power Switch

3.7

Fuel Line Fitting

7

Motor Bracket

28

Right Side Cover

3.8

Ignition Electrode

8

Lower Shell

29

Window Display

3.9

Screw

9

Oil Outlet Plug

30

Fuel Cap

4

Fan Assembly

10

Fuel FIlter

31

Clip Nut

5

Motor and Pump Assembly

11

Left Side Cover

32

Thermostat Bracket

5.1

Motor

12

Ignitor

33

Thermostat Limit Control Assembly

5.2

Pump Body

13

Capacitor

34

Air Line Hose

5.3

Plastic Connector

14

Grounding Plate

35

Fuel Line Hose

5.4

Rotor Kit

15

Fixation Part

36

Ignitor Wire

5.5

Blade

16

Fuel Tank

37

Photocell

5.6

End Pump Cover

17

Supporting Bracket

38

Photocell Bracket

5.7

Output Filter (small)

18

Power Cord

39

Fuel Gauge

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Fuel oil

The fuel oil must be drained from the device and collected.
Fuels are to be disposed of according to the national
regulations.

Summary of Contents for IDX 30 D























Reviews: