EN
13
air cooler PAE 19 H
Switching the device on
Once you have completely installed the device as described in
the chapter Assembly and start-up, you can switch it on.
1. Press the on/off switch (
6
) into position
I
.
ð
The device is now in standby mode.
2. Press the
on/off
button (
16
).
ð
An acoustic signal is emitted.
ð
The device starts in ventilation mode at fan stage 1.
ð
The
On
17
,
Ventilation
(
31
) and
Fan stage 1
LEDS (
19
)
are lit.
Setting the operating mode
The device comes with the following operating modes:
•
Air cooling
•
Ventilation
•
Air freshening
•
Night mode
•
Heating function
Air cooling
The air cooling mode can be switched on in addition in the
ventilation, air freshening and night mode.
During air cooling the pump is switched on and the water is
distributed over the evaporation filter to cool the circulating air.
Please proceed as follows to activate air cooling:
ü
The water tank (
13
) must be filled up with water at least to
the minimum filling level.
1. Press the
air cooling
button (
27
).
ð
The
air cooling
LED (
26
) is lit.
ð
The pump starts.
2. Press the
Fan speed
button (
18
) to set the desired fan
stage (1 to 3).
3. Press the
Air cooling
button (
27
) again if you wish to
switch off the
air cooling
.
ð
The
air cooling
LED (
26
) goes out.
ð
The device continues to run in the previously selected
operating mode with the pump being switched off, the
fan stage is maintained.
Note
When the Air cooling mode is activated, the air and
evaporation filter must not be removed, otherwise the
water from the filter will drip down into the device.
Note
If there is only a small quantity or no water in the water
tank, the Air cooling mode is switched off after 45 s
and an acoustic warning signal is emitted.
Ventilation
In ventilation mode, you can select all 3 fan speeds manually.
Please proceed as follows to adjust the fan speed:
1. Press the
Mode
button(
30
) until the
Ventilation
LED (
31
) is
lit.
2. To adjust the fan stage, press the
Fan speed
button (
18
)
until the LED for the desired
Fan speed
(
19
) is lit.
Air freshening
In
air freshening
mode, the fan speed increases and decreases
alternately to generate a pleasant, natural air stream.
Please proceed as follows to activate
air freshening
:
1. Press the
Mode
button(
30
) until the
Air freshening
LED (
29
)
is lit.
ð
The fan stages are automatically adjusted.
Night mode
In night mode, the device operates using a preset programme
with different fan speeds to generate an air stream that is
adapted to human sleeping habits.
Night mode can be activated in combination with the 3 fan
stages and
air cooling
.
•
At fan stage 1, the device runs permanently at this stage.
•
At fan stage 2, the device automatically switches to fan
stage 1 after an operating time of 30 minutes and keeps
running at this speed.
•
At fan stage 3, the device automatically switches to fan
stage 2 after an operating time of 30 minutes. After
another 30 minutes, the device automatically switches to
fan stage 1 and runs permanently at this stage.
Proceed as follows to switch on the
Night mode
:
1. Press the
Mode
button (
30
) until the
Night mode
LED (
28
)
is illuminated.
2. Press the
Fan speed
button (
18
) until the LED for the
desired
Fan speed
(
19
) is lit.
Heating function
In the Heating function mode, the device generates a warm air
stream.
1. Press the
Heating function
button(
21
) until the LED for the
desired heating level (
20
) is lit.
ð
The device runs on the heating level selected.
2. To switch off the heating function, press the
Heating
function
button (
21
) until the LEDs for the heating level (
20
)
go out.
ð
The heating function mode is switched off.
Note
After switch-off, the fan continues running for
approx. 10 seconds to cool down the device and to
prevent overheating.
