![background image](http://html1.mh-extra.com/html/tronair/02-1032c0111/02-1032c0111_operation-and-service-manual_1171167010.webp)
Models: 02-1032C0111, 02A1032C0111, 02B1032C0111, 02C1032C0111,
02A1032C00150
10 Ton Single Stage Jack
02/2014 | Rev. 01
Page | 7
7.4.2
Jack Instructions
(continued)
3. Close pump release valve by turning clockwise.
NOTE: Turning the pump release valve counter-clockwise lowers the jack. Turning the pump release valve clockwise
stops the jacks descent, and allows it to be raised.
4. Operate the pump using the handle, or by holding the lever on the air valve if equipped with an air pump.
5. Lower ram locknuts as aircraft is raised.
WARNING!
The ram locknuts are user operated safety devices. Failure to utilize these locknuts may result in personal
injury or death.
To Lower Aircraft:
1. Lower all jacks simultaneously.
2. If ram locking nut(s) is tight, raise jack slightly to release nut(s).
3. Loosen pump release valve slightly to slowly lower aircraft. Raise locking nut(s) as jack ram(s) lower.
NOTE: When using jack during washing operations, completely cover top of jack near ram seal.
CAUTION!
Do not place hands on top of jack near ram locknuts while lowering jack. Pinch points exist between top of
jack and threads on ram.
Always wear safety glasses.
8.0
TRAINING
Training of operating personnel is the responsibility of the employer. This jack must be used in accordance with aircraft
manufacturer’s instructions.
9.0
MAINTENANCE
9.1
GENERAL
All maintenance and/or repair work should be done using good workmanship practices and proper tools.
The work area should be clean and free of dirt.
When O-rings and backup rings are removed, every effort should be made to avoid the contact of tools with the critical
surfaces of parts. Surface deformities could cause degradation of seals and failure.
It is good practice to replace both O-rings and back-up rings once removed. Cut and damaged O-rings normally result in
fluid leakage.
If cylinder bore is found to be rusty, it may be honed to a maximum diameter of 3.257 inches (82.73 mm) and a surface
finish of 16 micro inches. If pitting in the bore cannot be removed by this process, the jack cylinder must be replaced
before the jack can be returned to service.
At this time, flush old hydraulic fluid and dirt from overall system and replenish with new, clean hydraulic fluid.
When refilling the hydraulic system the characteristics of the hydraulic fluid used in the jack and the level of the hydraulic
fluid as it is noted on the jack shall be observed.
Jacks shall be maintained and repaired in accordance with the
manufacturer’s instructions. Such maintenance and repair
shall be carried out by qualified persons.
No modifications shall be carried out which adversely affect the compliance of the jack with draft standard 2006/42/EC.
9.2
MAINTENANCE SCHEDULE
Check Fluid Level ............................ Each Use
Lubricate Casters ............................ 3 Months
Cleaning .......................................... Annually Or As Needed
NOTE: Wipe with soft cloth only, do no pressure wash or spray water directly at ram seal.
9.2.1
Storage/Low Usage
If jack is unused for 90 days, raise ram to full hydraulic extension, spray ram with DoALL RPM, LPS or equivalent water
repellant, BUNA N compatible lubricant.
Summary of Contents for 02-1032C0111
