background image

14

SAFETY PROCEDURES 

  Never allow unauthorized persons to operate lift. Thoroughly train new employees in the operation and care of lift. 

 

Caution: the power unit operates at high pressure. 

 

Remove passengers before raising vehicle. 

 

Prohibit unauthorized persons from being in shop area while lift is in use. 

 

Total lift capacity is 

11,

000Lbs with 2

,7

50lbs per arm pad. Never exceed the capacity. 

  When approaching the lift with a vehicle, center the vehicle between the columns so that the tires will clear the 

swing arms easily. Slowly drive the vehicle up between the posts. Have some one outside the vehicle guide the 

driver. 

  Always lift vehicle using all four arms. Never use lift to raise one end or one side of vehicle. 

  Prior to lifting vehicle, walk around the lift and check for any objects that might interfere with the operation of lift 

and safety latches; tools, air hoses, shop equipment. 

  Raise vehicles about 3” and check stability by rocking. 

  Prior to lowering vehicle, walk around the lift and check for any objects that might interfere with the operation of lift 

and safety latches; tools, air hoses, shop equipment. Swing the arms out of the path and slowly drive the vehicle 

out. Have some one outside the vehicle guide the driver. 

ALWAYS LOCK THE LIFT BEFORE GOING UNDER THE VEHICLE. 

NEVER ALLOW ANYONE TO GO UNDER THE LIFT WHEN RAISING OR LOWERING. 

Call 866-563-5438 For Help

14

TRIUPMH AUTO LIFTS 

TRIUPMH AUTO LIFTS 

TRIUPMH AUTO LIFTS

Summary of Contents for NT-11



















Reviews: