Triumph 2010 Rocket III Handbook Download Page 40

Page: 40 / 108

How to Ride the Motorcycle

To Stop the Engine

1. Ignition switch
2. Engine stop switch
3. Starter button

Note:

•

When using the side stand, always
turn the handlebars fully to the left
and leave the motorcycle in first
gear.

Support the motorcycle on a firm, level
surface with the side stand.

Close the throttle completely.

Select neutral.

Turn the ignition switch off.

If parking:

Lock the steering.

Remove the key.

Engage first gear.

For instructions on safe parking, (see
page

cbmp1

ceno

Caution

The engine should normally be stopped by
turning the ignition switch to the OFF
position. The engine stop switch is for
emergency use only. Do not leave the
ignition switched on with the engine
stopped. Electrical damage may result.

Summary of Contents for 2010 Rocket III













































































































Search results

Summary of Contents for 2010 Rocket III

Reviews:

Related manuals for 2010 Rocket III

Brands by name

Popular brands

Triumph 2010 Rocket III, Handbook

Search results

Summary of Contents for 2010 Rocket III

Reviews:

Related manuals for 2010 Rocket III

Brands by name

Popular brands