Triton V575W User Manual Download Page 4

                                                                                                    - 

  -                                                                XM155  V1.0  NR           

                 

 

 

If the device has been exposed to temperature changes due to environmental changes, do not switch 
it on immediately. The arising condensation could damage the device. Leave the device switched off 
until it has reached room temperature. 
 
This device falls under protection-class I. Therefore it is essential that the device be earthed. 
The electric connection must carry out by qualified person. 
 
The device shall only be used with rate voltage and frequency.

 

Make sure that the available voltage is not higher than stated at the end of this manual. 
 
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, 
replacement of the cable must be done by an authorized dealer. 
 
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle 
the power cord by the plug. Never pull out the plug by tugging the power cord. 
During initial start-up some smoke or smell may arise. This is a normal process and does not 
necessarily mean that the device is defective, it should decrease gradually. 
 

 

 

Please be aware that damages caused by manual modifications to the device are not subject to 
warranty. Keep away from children and non-professionals. 
 

GENERAL GUIDELINES 

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc. 
This fixture is only allowed to be operated with the max alternating current which stated in the 
technical specifications in the last page of this manual, the device was designed for indoor use only. 
Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure 
that the device will serve you for a long time without defects. Do not shake the device. 
Avoid brute force when installing or operating the device. 
The device shall only be used complete with its protective shield. 
 
While choosing the installation-spot, please make sure that the device is not exposed to extreme heat, 
moisture or dust. The minimum distance between light-output from the projector and the illuminated 
surface must be more than 0.5 meter. 
 

Summary of Contents for V575W






















Reviews: