background image

T8 0 s i

2

ADVICE TO USERS

The following points will help you
understand how the shower operates:

1

The electric heating elements operate at a

constant rate at your chosen power setting.
It is the flow rate of the water passing
through the heater unit which determines
the shower temperature at any given
setting. (The slower the flow the hotter the
water becomes, and the faster the flow the
cooler the water).

2

During Winter, mains water supply will be

cooler than in Summer. Therefore the
temperature of the shower will vary
between seasons on any one setting of the
temperature control, e.g. if you have chosen
setting number 6 as your preferred shower
temperature in the Summer, you will have to
increase that number during Winter by
adjusting the temperature control clockwise
(which in effect slows the water flow). 

3

The stabiliser valve minimises variations in

shower temperature during mains water
pressure changes. If changes in shower
temperature are experienced during normal
use, it will most likely be caused by the
water pressure falling near to or below the
minimum level. The drop in pressure may be
due to water being drawn off at other
points in the house whilst the shower is in
use. If pressure drops appreciably below the
minimum, the heating elements will
automatically cut out. 

If ever the water becomes too hot and
you cannot obtain cooler water, first
check that the sprayplate in the
sprayhead has not become blocked.

Replacement parts can be ordered from
Customer Service. See 

‘spare parts’

for

details and part numbers.

Due to continuous improvement and updating,
specification may be altered without prior notice.

INTRODUCTION

This book contains all the necessary fitting
and operating instructions for your Triton
T80si electric shower. Please read them
carefully. 

The shower installation must be

carried out by a suitably qualified person
and in the sequence of this instruction book.

Care taken during the installation will ensure
a long, trouble-free life from your shower.

SPECIFICATIONS

Electrical

Nominal power

Nominal power

rating at 240V

rating at 230V

7.5kW – (32A MCB rating)

7.0kW – (32A MCB rating)

8.5kW – (40A MCB rating)

7.9kW – (40A MCB rating)

9.5kW – (40A MCB rating)

8.8kW – (40A MCB rating)

Water

Inlet connection – 15mm diameter.
Outlet connection – 1/2 ”  BSP male thread.

Entry Points

Water – top, bottom, back, left or right.
Cable – top, bottom, back, left or right.

Materials

Backplate, cover, controls, sprayhead – ABS.
Sprayplate – Acetal.
Elements – Minerally insulated corrosion resistant
metal sheathing.

Dimensions

Height - 300mm
Width - 208mm
Depth - 110mm

Standards and Approvals

Triton is registered by the British Standards
Institute to BS EN  ISO 9001:1994.

Complies with the requirements of current British
and European safety standards for household and
similar electrical appliances.

Complies with requirements of the British
Electrotechnical Approvals Board (BEAB).

Meets with Compliance with European
Community Directives (CE).

Summary of Contents for Topaz T80si

























Reviews: