background image

Gemini Profiler with Survey Software

0695-SOM-00009, Issue: 01

4

© Tritech International Ltd.

Help & Support

First please read this manual thoroughly (particularly the Troubleshooting section,

if present). If a warranty is applicable, further details can be found in a Warranty

Statement at the end of the manual.

Tritech International Ltd

 can be contacted as follows:

Mail

Tritech International Ltd

Peregrine Road

Westhill Business Park

Westhill, Aberdeenshire

AB32 6JL, UK

Telephone

++44(0)1224 744 111

Fax

++44(0)1224 741 771

Email

[email protected]

Website

www.tritech.co.uk

Prior  to  contacting 

Tritech  International  Ltd

  please  ensure  that  the  following  is

available:

1. The Serial Numbers of the product and any 

Tritech International Ltd

 equipment

connected directly or indirectly to it.

2. Software or firmware revision numbers.

3. A clear fault description.

4. Details of any remedial action implemented.

Contamination

If the product has been used in a contaminated or hazardous environment

you 

must

  de-contaminate  the  product  and  report  any  hazards 

prior

  to

returning the unit for repair. 

Under no circumstances should a product be

returned that is contaminated with radioactive material.

The  name  of  the  organisation  which  purchased  the  system  is  held  on  record  at

Tritech International Ltd

 and details of new software or hardware packages will be

announced at regular intervals. This manual may not detail every aspect of operation

and for the latest revision of the manual please refer to 

www.tritech.co.uk

Tritech International Ltd

 can only undertake to provide software support of systems

loaded with the software in accordance with the instructions given in this manual. It

is the customer's responsibility to ensure the compatibility of any other package they

choose to use.

Summary of Contents for Gemini 620pd


















Reviews:

Related manuals for Gemini 620pd