manualshive.com logo in svg

Triplett GSM450, User Manual

Share
Download
Triplett GSM450 User Manual Download Page 14

 
 

2.

 

Short press the MXMN/AV/

 button to advance to set the 

sampling rate for datalogging. The hour digit will blink in the 
secondary display. 

3.

 

Short press the H/

 button to increase the time or short 

press the MEM/

 button to decrease the time. 

4.

 

Short press the MXMN/AV/

 button to save the setting 

and advance to the minute setup. 

5.

 

Short press the H/

 button to increase the time or short 

press the MEM/

 button to decrease the time. 

6.

 

Short press the 

 button to save the setting and 

advance to the second setup. 

7.

 

Short press the M

 button to save the settings and 

return to P40. 
8.

 

Short press the 

 button to exit without saving. 

9.

 

Short press the 

 button to advance to the next step. 

 

Note: The datalogging sampling range is from 1 second to 4 hours 59 
minutes 59 seconds. 
 

P50 Changing the Barometric Pressure Compensation 

1.

 

When in pressure setup mode, P50 and “PrES” display on the 
LCD. Short press the H/

 button to advance to P50 if 

necessary. 

 

2.

 

Short press the MXMN/AV/

 button to set the pressure 

compensation value for the CO

2

 measurement. The current 

pressure compensation value in hPa will flash on the LCD. 

3.

 

Short press the H/

 or MEM/

 button to adjust the 

barometric pressure value. The pressure compensation 
range is from 70 to 199 hPA. 

 

4.

 

Short press the MXMN/AV/

 button to save the setting and 

return to P50. 

 

5.

 

Short press the 

/ESC button to exit without saving. 

6.

 

Short press the H/

 button to advance to the next step. 

 

Summary of Contents for GSM450





















Reviews:

No comments

Brands by name

Popular brands

Load more brands