background image

INSTRUCTIONS FOR USE

ENGLISH

9100001306 - Jaguar 26R

27

04/2015

FUSE CHECK/REPLACEMENT

NOTE

All machine electrical circuits are protected by auto-resettable electronic devices. The safety fuses activates only in case 

of serious damage. 

It is recommended to have the fuses replaced by qualified personnel only. 

Refer to the Service Manual available at any authorized Retailer.

SAFETY FUNCTIONS

The machine is equipped with the following safety functions.

EMERGENCY PUSH-BUTTON

It is located in an easily accessible position (8). Press it firmly in case of immediate necessity to stop all machine functions.

To reset the machine operation, lift the tank assembly (44) and reconnect the battery connector (9).

ANTI-SKID SAFETY SYSTEM

This system reduces the speed when turning and when the machine tilts laterally to avoid sudden skids, this increasing the machine 

stability in any condition.

DRIVER’S SEAT MICROSWITCH

It is located inside the driver’s seat and it does not allow the machine drive system to operate if the operator is not seated on the 

driver’s seat.

ELECTROMAGNETIC BRAKE

It is built-in the front wheel and keeps the machine braked when the machine is off or stopped.

Summary of Contents for JAGUAR 26R

































Reviews: