manualshive.com logo in svg
background image

This operator’s book has important information for the use and safe operation of this machine.  Read this book carefully before 
starting the machine.  Keep this book near the machine, protected from liquids and other substances that can cause damage to it.  
If you do not follow the instructions, you can cause an injury or damage equipment, furniture or buildings.

For new books, please download your copy from our website www.pacificfloorcare.com or write to: 
               Pacific Floorcare

TM

               2259 S. Sheridan Drive
               Muskegon, MI  49442-6252

Carefully inspect all components to ensure that there is no concealed freight damage.  If such damage is discovered, file a 

 

“CONCEALED DAMAGE REPORT” immediately with the delivering carrier. 

The contents of this manual are based on the latest product information available at the time of publication.  Pacific Floorcare 

 

reserves the right to make changes or improvements without being obliged to apply changes to the machines previously sold.

Thank you for purchasing a Pacific Floorcare product.  Warranty registration will allow us to better serve you over the lifetime of 

the product.  For quick and easy registration,  go to:  www.pacificfloorcare.com/Register Product.

PLEASE READ THIS BOOK

S-20 20-INCH 

AUTO SCRUBBER

PARTS & OPERATING MANUAL

Содержание S-20


























































Отзывы: