Triotech Storm VR Owner'S Manual Download

Page: 33 / 72

Preventive Maintenance

Storm-OM-001

28 February 2020

This document, including the information contained herein, is proprietary to Triotech Amusement Inc.

Preventive Maintenance

8.1

Daily

1) Everything is
fine. No
adjustments

nic

ian

2) Adjustment
made
3) Repaired/
Replaced
Component
4)Out of Service

Pre-Opening
Procedures:

Storm and Motion base
Daily Cleaning Schedule

Clean the seat
footrest

Ensure all areas are
free from trash and
other debris

Audio/Visual

Make sure the HTC
Vive helmet is
functional

Ensure that the HTC
Vive helmet lenses
are clean.

Verify all speakers
and subwoofer are
operational

Verify that the
Special effects are all
working

Leap Motion

Plastic casing is in
good condition

Ensure that the leap
motion controller is
functioning properly.

Seats

Inspect seats and
safety rubber below
seat for rips

Ensure that the seats
are clean.

The Lapbar is
functioning properly.

Summary of Contents for Storm VR









































































Search results

Summary of Contents for Storm VR

Reviews:

Related manuals for Storm VR

Brands by name

Popular brands

Triotech Storm VR, Owner'S Manual

Search results

Summary of Contents for Storm VR

Reviews:

Related manuals for Storm VR

Brands by name

Popular brands