manualshive.com logo in svg

Trinity EagleBed, Manual, Page: 23 / 31

Share
Download
Trinity EagleBed Manual Download Page 23

 

 

May 2022 

 

23 

©2022-2023 Trinity Trailer Mfg., Inc

. 

 
 

 

Figure 15- Entering Truck Bed Warning. 

 

Figure 16- Moving Conveyor Crush Warning 

 

HYDRAULIC SYSTEM SERVICING 

 

TRACTOR HYDRAULIC SYSTEM REQUIREMENTS 

 
Gear Pump Requirements (Volume):  

 

10-30 GPM (Gallons per Minute) 

Reservoir capacity:    

 

 

 

Minimum 5 Gallons 

Hyd. Pressure Requirements/Bypass Settings: 

2500 PSI/3000 PSI 

Filtration Requirement: 

 

 

 

10 

μm 

 

Tractor hydraulic oil must be maintained at all times.  Neglect of the tractor oil will result 
in premature hydraulic component failure.   
 
If the truck bed was ordered with “Food Grade” hydraulic oil the tractor must also have 
“Food Grade” hydraulic oil or it will contaminate the truck bed’s hydraulic system.  
 

 
Contact our parts department toll free at 800-235-6577 to order a replacement filter 
(Figure 18). 

  

       

 

!

WARNING

 

 

IF THE TRACTOR IS NOT EQUIPPED WITH A 
PRESSURE VALVE, A CLOGGED FILTER CAN 
CAUSE AN OVERPRESSURE SITUATION THAT 
CAN DAMAGE HYDRAULIC HOSES AND PUMPS 

Summary of Contents for EagleBed
































Reviews:

No comments