Trilux LiveLink System Manual Download Page 20

Page: 20 / 77

“LIVELINK INSTALL” APP / WHAT IS A USE CASE? / PUBLIC USE CASES

Page 20 / 77

WHAT IS A USE CASE?

Each LiveLink room is set up based on a Use Case. A Use Case is a

pre-configuration that simplifies the further setup of the room.

A Use Case defines:

• The number of luminaire groups (presentation of a schematic

matching the room type)

• The assignment between sensors and luminaire groups

• Scenes included in the delivery (which, of course, can be supplemented

by scenes you created on your own)

In addition to the placement of luminaire groups, a Use Case also

includes a pre-configuration of the sensors.

A Use Case constitutes the foundation of the room setup. If individualised

Use Cases are needed, these can be created in cooperation with the

TRILUX light planners and loaded for utilisation as “Private Use Cases”.

PUBLIC USE CASES

The public Use Cases are included in the delivery and can be updated in

the Use Case administration (see chapter “Use Case administration”).

The following Use Cases are going to be covered on the next pages.

Office

Industry

Education

Shop & Retail

Health & Care

General

• Small Office

• Large Office

• Conference Room

• Manufacturing

Hall, simple

• Manufacturing

Hall, expanded

• Classroom

• Individual Sports

Hall

• Retail

• Patients' room

• Corridor

• Universal

(See chapter “Univer-
sal Use Case”)

After completion of the steps for commissioning, the scenes pre-set

in the Use Cases can be adjusted or additional ones added. You can,

for example, change the switch-off delays, switch from fully automatic

to semi-automatic operation, or change the dimming level.

The daylight-dependent control requires an initial calibration with the

help of an illuminometer (see chapter “Administrating scenes”).

Summary of Contents for LiveLink














































































Search results

Summary of Contents for LiveLink

Reviews:

Related manuals for LiveLink

Brands by name

Popular brands

Trilux LiveLink, System Manual

Search results

Summary of Contents for LiveLink

Reviews:

Related manuals for LiveLink

Brands by name

Popular brands