Tridonic LuxControl DALI XC Manual Download | Manualshive

Page: 13 / 29

background image

Commissioning

DALI XC_IB 3.0 | 01.2014 | en

13

5.1

Starting commissioning

Starting commissioning with DALI XC in "Prog" operating mode

i

Note

Existing assignments of luminaires to groups are deleted.

Starting may take several minutes depending on the number of connected luminaires.

1. Hold down momentary-action switch (approx. 10 s).

2 beeps sound at the beginning.

3 beeps sound after another 10 s.

2. Release momentary-action switch.

Assignment of all luminaires to groups has been deleted.

Programming mode is enabled.

All luminaires are dimmed to the minimum value.

All luminaires are brightened one after the other.

All luminaires are then dimmed to the minimum value again.

1 beep sounds.

One luminaire brightens.

Figure 3: Starting commissioning (DALI XC in "Prog" operating mode)

«
...
11
12
13
14
15
...
»

Summary of Contents for LuxControl DALI XC






























Reviews:

No comments

Related manuals for LuxControl DALI XC

Brand: ABB Pages: 2

Brand: KEENZ Pages: 24

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

GAT ACCESS 6100

Brand: Gantner Pages: 4

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brand: Rain Bird Pages: 138

Brand: Watts Pages: 8

Brand: Jäger Pages: 18

Brand: Measurement Computing Pages: 32

Travel About Series

Brand: Kolcraft Pages: 14

Brand: Miller-Leaman Pages: 18

Brand: Samson Pages: 70

Brand: Keysight Technologies Pages: 105

Brand: Delta Pages: 16

Turbo-V 250 series

Brand: Varian Pages: 79

Brand: M-system Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands