manualshive.com logo in svg

Trident DRYSPELL PLUS 10, Manual

Share
Download
Trident DRYSPELL PLUS 10 Manual Download Page 20

Section 6

Installation

6.1 General

l

Make sure that the dryer is not close to any equipment that does not comply with EU directive 2004/108/EC (relating
to electromagnetic compatibility) and that may affect the operation of the dryer.

l

Do not drop the dryer or lift it by the piping or control panel. Doing so may damage the dryer.

l

Ensure that the dryer is installed in the vertical position.

6.2 Location

l

Install the dryer in a closed, clean, dry room protected from freezing

l

Access to the room should be restricted to personnel qualified in the maintenance and operation of Dryspell Plus dryers

l

The room must be adequately ventilated

l

The dryer must not be directly exposed to sources of heat

l

The temperature of the room must not exceed 43°C (109°F)

6.3 Layout

l

There must be a minimum distance of 3 feet between the dryer and any other equipment around it that uses electricity

6.4 Air line

Figure 6. Bypass arrangement to be provided on air line

l

Install a system of bypass valves between the dryer inlet and outlet as shown in Figure 6 so that the dryer can be
serviced without having to interrupt the compressed air supply from the circuit

l

If the dryer has been bought without a pre-filter, install a suitable filter ahead of the dryer

l

The upstream and downstream valves must be closed during installation

6.5 Manpower required

l

One skilled technician

6.6 Tools required

l

Standard tool set

6.7 Procedure

l

Secure the dryer by bolting it down

l

Connect a drain line to the pre-filter

l

Check for leaks after all connections have been made

13

Summary of Contents for DRYSPELL PLUS 10







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands