background image

Trident Emergency Products, 

LLC

2940 Turnpike Drive | Suite #9 | Hatboro, PA 19040 USA
215-293-0700 

Phone

215-293-0701 

Fax

[email protected] 

Email

TridentDirect.com

World Class 

Fire Industry 

Products

AirPrime™ is a trademark of 

Trident Emergency Products, LLC

Repair/Replacement Parts

#02.003.1e 

 06/25/2019

REF #

DESCRIPTION

PART #

1a

Solenoid Valve 12-Volt

30.003.2

1b

Solenoid Valve 24-Volt

30.003.3

2

Air Filter Replacement for 1/4" NPT Bore

21.002.0

3

Piston

11.001.0

4

Valve Stem

05.002.0

5

Seal Washer

04.004.0

6

3/4" Wye Strainer (Replacement Screen: 21.003.1)

21.003.0

7

Rebuild Kit (Seals, Mesh Filter, Spring Valve Plate, Fasteners)

27.003.3

8

Pressure Protection Valve (PPV)

30.053.0

9

Lift Gauge

14.006.0

10a

Rocker Switch 12-Volt and Label Assembly

27.003.5

10b

Rocker Switch 24-Volt and Label Assembly

27.003.6

11

Label Only: 

Rocker Switch

02.004.2

12

Pressure Switch and Connector

40.002.1

13a

Rocker Switch 12-Volt, Label, Mounting Plate, Lift Gauge Assembly

27.003.7

13b

Rocker Switch 24-Volt, Label, Mounting Plate, Lift Gauge Assembly

27.003.8

14

Label Only: 

Rocker Switch with Lift Gauge

02.004.4

REF #

DESCRIPTION

PART #

15a

Rocker Switch 12-Volt Replacement

40.001.2

15b

Rocker Switch 24-Volt Replacement

40.001.3

16

Wiring Harness for Auto AirPrime

41.001.0

17

Push Button, Label, and Mounting Plate Assembly

27.003.1

18

Label Only: 

Push Button

02.006.4

19

Push Button Replacement

30.005.3

20

Push Button, Label, Mounting Plate and Lift Gauge Assembly

30.005.4

21

Label Only: 

Push Button with Lift Gauge

02.006.10

22

Remote Priming Valve (RPV)

30.035.1

23

1/4" NPT Air Check Valve

30.012.0

24a

Remote Priming Valve with 12-Volt Solenoid

30.035.10

24b

Remote Priming Valve with 24-Volt Solenoid

30.035.11

25

Multi-Location Push-Button w/ Mounting Plate

27.003.9

26a

Label Only: 

Primer Front Intake

02.006.5

26b

Label Only: 

Primer Rear Intake

02.006.6

26c

Label Only: 

Primer Left Side

02.006.7

26d

Label Only: 

Primer Right Side

02.006.8

AirPrime Conversion Kits and Rebuild Kit

Conversion Kit:

 Single Location AirPrime System, Converts Manual to Automatic

27.014.0

Conversion Kit: 

Multi-Location AirPrime System, Converts Manual to Automatic

27.014.1

Conversion Kit: 

Manual AirPrime System, Converts Single (1) Location to Dual (2) Location

27.005.2

Conversion Kit: 

Automatic AirPrime System, Converts Single (1) Location to Dual (2) Location

27.005.3

Conversion Kit: 

Multi-Location AirPrime System, Adds Additional Locations Going From (2) Location to (3) Location. 

Or From (3) Location to (4) Location

27.005.1

Conversion Kit: 

Automatic AirPrime System, Adding a Lift Gauge to existing Automatic AirPrime. Requires .125" NPT Port. Contact Factory for Details

27.005.5

Conversion Kit: 

Manual AirPrime System, Adding a Lift Gauge to existing Manual AirPrime. Requires .125" NPT Port. Contact Factory for Details

27.005.4

Conversion Kit: 

Manual AirPrime, Converting to Auto with Lift Gauge. Requires .125" NPT Port. Contact Factory for Details

27.005.6

Rebuild Kit:

 Contains Seals, O-Rings, Spring Valve Plate, Domed Inlet Filter and Fasteners

27.003.3

26

6

7

8

9

12

15

16

19

22

24

25

1

5

4

6

2

10

a,b

11

13

a,b

14

17

18

20

21

Automatic

AirPrime Parts

Manual

AirPrime Parts

Multi-Location

AirPrime Parts

Air F

low

23

3

21.003.1

a,b

a,b,c,d

a,b

a,b

Summary of Contents for AirPrime Series

















Reviews: