TRIATEK UVM-1000 Installation Manual Download Page 1

Page: 1 / 34

UVM-1000

Universal Valve Module

LIT-12013155

September 2020

Installation Guide

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area may cause harmful interference, in which case users will be required to correct the interference at their own expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

IMPORTANT

: The UVM-1000 Universal Valve Module must be wired to 24 VAC only. Wiring the unit to 110 VAC will cause serious

damange and void the warranty.

Risk of Property Damage.

Ensure that the power source conforms to the requirements of the equipment. Failure to use a correct power source may result in

permanent damage to the equipment.

Risque de dégâts matériels.

S’assurer que la source d’alimentation électrique est conforme aux spécifications de l’équipement. L’utilisation d’une source

d’alimentation électrique inappropriée risque d’endommager irrémédiablement l’équipement.

North American Emissions Compliance

United States

Summary of Contents for UVM-1000



































Search results

Summary of Contents for UVM-1000

Reviews:

Related manuals for UVM-1000

Brands by name

Popular brands

TRIATEK UVM-1000, Installation Manual

Search results

Summary of Contents for UVM-1000

Reviews:

Related manuals for UVM-1000

Brands by name

Popular brands