TRIATEK FMS-2000M Lite Installation Manual Download Page 20

Page: 20 / 23

FMS-2000M Lite

LIT-12013692

BMS integration

Configuring the display module settings

FMS-2000M Lite DIP switch position

Demo mode

Run mode

Position 1

Position 2

Position 3

Off

Position 4

Off

Objects

Analog inputs

Read/Write

Availability of analog input objects
FMS2ML–BxR

AI-1

Analog input 1, differential pressure

Read only

Yes

Objects

Analog values

Read/Write

Availability of analog value objects
FMS2ML–BxR

AV-1

Network Variable temperature 1

Read or write

Yes

AV-2

Differential Pressure low alarm setpoint 1

Read or write

Yes

AV-3

Differential Pressure low warning setpoint 1

Read or write

Yes

AV-4

Differential Pressure high warning setpoint 1 Read or write

Yes

AV-5

Differential Pressure high alarm setpoint 1

Read or write

Yes

AV-6

Network Variable humidity 1

Read or write

Yes

Objects

Multistate value objects

Read/Write

Availability of multistate value objects
FMS2ML–BxR

MV-1

AI-1 Alarm Status
1 = positive, 2 = negative, 3 = neutral

Read only

Yes

Summary of Contents for FMS-2000M Lite
























Search results

Summary of Contents for FMS-2000M Lite

Reviews:

Related manuals for FMS-2000M Lite

Brands by name

Popular brands

TRIATEK FMS-2000M Lite, Installation Manual

Search results

Summary of Contents for FMS-2000M Lite

Reviews:

Related manuals for FMS-2000M Lite

Brands by name

Popular brands