manualshive.com logo in svg

Tri-Clover 741 Series, Service & Installation Manual

Share
Download
Tri-Clover 741 Series Service & Installation Manual Download Page 9

- 9 -

SHUT OFF

Lubricate o-ring with Tri-Clover L1011 Sanitary Silicone Spray.
Insert o-ring and split bushing into bonnet.

DIVERT AND ELBOW

Lubricate o-ring with Tri-Clover L1011 Sanitary Silicone Spray.
Insert o-ring into body, place required washer or sleeve on top
of o-ring, place split bushing on top of this component.  Fasten
bonnet or body to yoke with three bolts and lock washers.

IMPORTANT:

 Replace nylon lock before threading valve stem

onto actuator stem, see  section 

TYPE 10, 20 & 30 Actuator.

MAINTENANCE

Shut Off

Divert & Elbow

DIVERT AND ELBOW

Apply 60psig air to actuator - (Normally Open Divert and Normally Closed Elbow Valves Only).

SHUT OFF, DIVERT, ELBOW & KETTLE

Push valve stem through bonnet until it meets the actuator stem.  Partially thread valve stem onto
actuator stem by hand until nylon lock resistance is felt.  Apply an open end wrench over the
valve stem flats, turn clock wise and tighten until valve stem meets actuator stem shoulder.

Place gasket in body groove and clamp together.  Cycle valve at least 6 times.  Operate all
valves after assembly to be sure they are operating correctly.  Inspect all air line connections for
leaks.

Summary of Contents for 741 Series
































Reviews:

No comments

Brands by name

Popular brands

Load more brands